Kitchenaid Dishwasher Parts

Ordered new basket. BUT NOTE, when model number was put in for the part to determine compatibility, it said it was NOT COMPATIBLE, but it absolutely fit just fine. Read more

• Will not fill with water

First I cleared the food chopper area. There were things there, bits of plastic for instance, but it wasn't the reason for the dishes not getting sprayed off. The dishwasher continued to only partially fill and not circulate the water. I started the dishwasher, let the pump start and then opened the door and filled up the dishwasher manually. It sprayed water as it should, cleaning the top rack quite well. I figured the issue was not the float switch, since some water was coming in. So I... Read more

Ordered a replacement part off another site that came in with an incorrect molded connection to the Spray Arm. The part broke my tabs on the Spray Arm and instead I bought both parts from this site. Both items were correct and resolved the issue. Read more

• Not cleaning dishes properly

Replaced upper and lower spray arms, plus nylon bearings. Read more

It was a learning experience. First I turned off the power! I removed the lower kick plate, disconnected the drain hose and electrical connectors. Then removed the discharge pump and heat sensor then loosened the 4 hold down arms/clamps. Then I opened the door and pulled the base up from the inside. Now to remove and replace the Pump Motor. Then reverse the process. If I were to do again, I'd pull the dishwasher out and lay it on its back. Read more

We looked for a supplier of the part and came across AppliancePartsPros. They had the parts in stock and the prices were reasonable. We ordered the parts sometime on Thursday afternoon. The needed parts arrived on Friday around 11:00A. Wow, what fast service! Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

Took my time and disasembeld the mixer and cleaned old grease from internal gear box. put new greas in and put it back together. A piece of cake!!!!! Read more

New door seal did the trick. Read more

• Will not dispense detergent

I ordered a new soap dispenser and began a new venture in repairing my dishwasher. I turned off the breaker that suppled power to the unit. I removed all the T-15 torx screws from the inside cover except one, which my wife helped me hold in. This prevents the cover from dropping off. Then, after removing those two, we closed the dishwasher cover, and lifted off the outside cover. That being off, I saw the two wires connecting the dishwasher dispenser solinoid. Removed them. Notice, that one... Read more

Bought a new baskit Read more

Replaced door lower seal and door gasket. Read more

As a homeowner, I love that I can just type my model number into Appliance Parts Pros website and find a listing/diagram of the entire unit. So when my dispenser on my dishwasher broke, I just ordered a new one. I use You Tube to watch videos on the specific repair, and then VOILA! I do the repair myself, saving at least a hundred dollars in a repair persons service call charge! While this repair was for my dishwasher, I've also fixed my washing machine, dryer, and steam humidifier. Read more

I think I could have just replaced the pump, but I chose to replace the whole assembly. The part is more expensive, but all the gaskets, etc, that come with it are new and that made sense to change all at once. I was able to change this in about 30 minutes, without removing the washer from the under-counter space. I did remove the front door panel, but in retrospect that was unnecessary and probably cost me more time than it saved. Empty the washer of parts, remove the front access panel.... Read more

I bumped into my KitchenAid dishwasher and the upper rack adjuster cracked. There was already a crack on the notch of the housing where the handle (lever) sits. In addition, the positioner popped out and I couldn't find it. So, I bought the three parts from AppliancePartsPros online. It arrived in about a week. The repair was fairly simple, but it still took about 45 minutes because I didn't want to crack the assemblies. For the housing, use a small slotted screwdriver to carefully... Read more