Kitchenaid Heating Element

This convection element supplies heat for your oven's convection mode. Working with the convection fan, it circulates hot air to maintain even, consistent baking and roasting performance.

• Provides the heat source during convection cycles for circulated-air cooking
• Helps maintain uniform cavity temperature and even browning
• Restores convection function when the original element is open or damaged
• Common symptoms: convection not heating, fan runs but little/no heat, longer or uneven cook times in convection

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks and the rear interior cover to access the element
• Remove mounting screws, pull the element forward, and transfer wires one at a time; ensure tight, secure connections
• Reinstall the cover, restore power, and run a brief convection test

This is a radiant surface heating element for smooth-top electric ranges. It replaces a failed burner to restore up to 1300 watts of even heat and dependable temperature control under the glass-ceramic cooktop. What it does:

• Generates radiant heat beneath the glass surface when powered by the burner control
• Restores proper heating if a burner will not heat, heats unevenly, or cycles off too quickly
• Helps eliminate long heat-up times caused by a weakened or open element
• Replaces elements with visible damage such as broken ribbons, burn spots, or charred terminals

• 1 radiant surface element (1300W)

• Disconnect power at the breaker or unplug the range before servicing
• Allow the cooktop to cool fully; lift/prop the glass top to access the element
• Note wire positions; transfer any mounting brackets/clips from the old element and reconnect wires securely
• Handle the element carefully and avoid stressing the ribbon; reassemble and test the burner before finalizing

This replacement heating element restores proper heat in electric dryers designed with two-level heat. It generates the controlled heat needed for both high and low temperature cycles, helping return normal drying performance.

• Heats the air passing through the drum during drying cycles
• Supports two-level heat so high and low temperature settings work correctly
• Typical symptoms include: no heat, insufficient heat, longer-than-normal dry times, or only one heat setting working
• A visibly broken coil or an open reading on a continuity test indicates failure

• Disconnect power before servicing; dryer circuits carry high voltage
• Handle the element carefully—coils and insulators are fragile; do not stretch or deform the coil
• Note wire locations and ensure tight, clean connections during reassembly
• Clear lint and verify airflow; restricted ventilation or failed thermostats/cutoffs can lead to repeat element failure

Restore top-heat performance with this Oven Broil Element. Mounted at the top of the oven, it delivers the radiant heat needed for broiling and finishing, helping ensure quick searing and even browning on the broil setting. What it does:

• Supplies radiant heat from above for broiling and top-browning
• Energizes during broil and any cycle that calls for upper-element heat
• Common symptoms: no broil heat, weak/uneven top browning, visible breaks or blisters on the element, or a tripped breaker when Broil is selected
• Replacing a failed element restores consistent upper-oven heat

• 1 broil element

• Disconnect power at the breaker before servicing
• From inside the oven, remove mounting screws and gently pull the element forward to access terminals
• Secure/label wires so they don't slip back through the rear panel; transfer leads one at a time
• Avoid bending or stressing the new element; ensure terminals are fully seated before restoring power

This radiant surface element uses a ribbon-style heater to provide even heat beneath a glass-ceramic cooktop. Replace a failing burner to restore consistent, reliable heating on the affected cooking zone.

• Provides radiant heat to one surface burner zone beneath the glass top
• Works with the surface control to regulate cooking temperature
• Common fix for a burner that won't heat, heats unevenly, or takes too long to heat
• Replace if the element shows an open circuit when tested for continuity

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the cooktop to cool completely; support the glass top per service instructions to access the element
• Transfer wires from the old element to the new one position-by-position; secure using existing brackets
• Avoid touching the element surface; test operation before reassembly

This surface heating element restores reliable heat to one burner on your electric range or cooktop. Replace a failed element to bring back consistent, controllable cooking performance and eliminate cold spots on the affected cooking zone.

• Supplies heat for a single surface burner on an electric range/cooktop
• Replaces a burned-out, shorted, or damaged element
• Common symptoms: no heat, uneven or intermittent heating, slow to heat, or visible damage/discoloration on the element
• Helps return proper response to the surface temperature control

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Access the element per your model's service manual; support the cooktop and handle components carefully
• Move wires over one at a time to the new element to avoid miswiring; secure mounting as originally installed
• Inspect wiring and terminals for heat damage; repair or replace any compromised connectors before reassembly

This 8-inch surface element restores reliable heating on an electric range or cooktop. Replace a failed burner to bring the cooking zone back to proper operation and consistent cooking performance. What it does:

• Provides heat for the 8-inch burner position on an electric range/cooktop
• Replaces an open or damaged element that no longer heats properly
• Can help resolve no-heat, slow/uneven heating, or intermittent heating issues
• Supports accurate temperature cycling when the element is functioning correctly

• 1 8-inch surface element

• Disconnect power to the appliance before servicing
• Allow the cooktop/range to cool completely before access
• Note wire locations and mounting/retaining hardware to transfer and reconnect exactly as found
• Handle the element carefully; avoid stressing the coil and ensure all electrical connections are secure before reassembly

This oven broil element mounts at the top of the oven to deliver direct radiant heat during the Broil cycle. Replacing a worn or burned-out element restores proper broiling performance and consistent top browning.

• Supplies top-down radiant heat when the oven is set to Broil
• Typical failure signs: broiler not heating, element won't glow, uneven top browning, visible cracks or blistering on the element
• Restores broil function when the original element is open or damaged

• Disconnect power at the breaker before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward
• Label/photograph wire positions; transfer the spade connectors securely and prevent wires from slipping back into the rear wall
• Ensure the element sits level and clear of the cavity surfaces; do not overtighten mounting screws

This is a dual radiant surface element for use with certain range models. The surface element supplies heat to the cooking area on the range's surface. If the element is not functioning correctly, the owner will not be able to use the range because it won't heat up.The dual radiant surface element is long-lasting, but this does not mean it will last forever. It could still need to be replaced if it wears out or is damaged. Shut off the circuit breaker to the range or unplug it before starting this replacement.The dual radiant surface element is sold individually. It is compatible with select models from Whirlpool, Maytag, and KitchenAid. This is a genuine OEM replacement part sourced from the manufacturer.

Replacement 8-inch surface heating element that restores reliable top-of-range heating for electric cooktops. Designed to match OEM fit and restore proper burner operation when the original element fails or heats unevenly. What it does:

• Produces heat for an 8-inch cooktop burner so cookware can reach cooking temperatures.
• Replaces a failed or damaged surface element that won't heat, heats intermittently, or heats unevenly.
• Fits ranges that use coil-style terminal surface elements; installs into the cooktop terminal block for direct replacement.
• Restores consistent heat output for normal stovetop cooking tasks.

• Disconnect power at the breaker before servicing the range to avoid shock.
• Allow the cooktop and element to cool completely and wear protective gloves to avoid cuts.
• Inspect the element terminals and terminal block for damage; seat the element fully into the terminal connections for a secure fit.

This heating element assembly is designed for 240-volt installations and restores proper heat to your appliance. Replace a burned-out element to bring temperatures back to spec and recover consistent, reliable performance. What it does:

• Generates the heat required on a 240V circuit to reach and maintain set temperatures
• Common failure symptoms: no heat or insufficient heat
• May show a visible break/hot spot on the coil or test open (no continuity)
• Intermittent or uneven heating can indicate a fatigued element or loose connections

• Disconnect power at the breaker/fuse and allow the appliance to cool completely
• Photograph/label wiring; transfer terminals to the new element one at a time
• Do not bend, stretch, or handle the coil surface with bare hands; mount securely per model guidance
• Check related high-limit/thermal devices, fuses, and wiring for continuity

This is the upper oven broil element that supplies direct high heat for broiling. It restores the oven's top-down heat for browning, searing, and finishing foods when the original element fails. What it does:

• Heats during the broil cycle to brown and sear food surfaces
• Replaces a cracked, burned, or non-heating broil element
• Visible signs of failure include discoloration, breaks, or no glow when in use

• Disconnect power at the breaker before accessing the oven; verify power is off
• Remove oven racks and access the element mounting screws inside the oven cavity
• Handle terminals carefully; avoid touching live contacts when reconnecting

This surface heating element restores reliable heat to an electric cooktop burner so pots and pans warm evenly and predictably. Replace a failed element to bring consistent performance back to your range or smooth-top cooktop.

• Supplies heat to a single cooking zone on an electric range or glass-top cooktop
• Replaces an element that is open, shorted, or intermittently heating
• Common symptoms: burner won't heat, heats unevenly, or only part of the zone glows
• Helpful when there is visible damage or hot spots on the element

• Disconnect power at the breaker; allow the cooktop to cool completely
• Access the element by lifting/removing the cooktop or from below
• Move wires one at a time to matching terminals; reuse any mounting clips/brackets as required
• Support the glass top during service and avoid stressing or scratching the surface

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

1200w. Size: 6 inch. Location: Left front, right rear, and left rear.

This broil element replaces the upper heating element in a conventional oven to restore broiling performance and even top-heat cooking. It fits into the oven cavity and connects to the existing element terminals for direct heating. What it does:

• Heats from the top of the oven to create intense, direct heat for broiling and finishing dishes
• Restores proper browning and crisping when the broil function fails
• Can resolve symptoms such as no broil heat, uneven top heating, or visible element damage
• Works with the oven's existing wiring and mounting points for straightforward replacement

• One broil element

• Disconnect power to the appliance at the breaker before starting any repair
• Allow the oven to cool completely and remove oven racks for access
• Handle the element by its insulated terminals; secure wiring connections and mounting screws firmly