Kitchenaid Hose Or Tube

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

This tube union connector joins two water or refrigerant tubes to restore a sealed flow path and stop leaks. It's a direct-replacement plumbing fitting used on refrigerators and ice/water systems. What it does

• Joins two sections of tubing to maintain a sealed water line connection.
• Restores proper water flow to the dispenser or ice maker when a damaged union causes leaks or loss of supply.
• Provides a threaded/press-fit junction to prevent drips and reduce pressure loss.
• Helps avoid water damage from a cracked or corroded tube joint.

• One tube union connector

• Turn off the water supply and unplug the appliance before starting work.
• Confirm tube sizes and connection type before installation; tighten fittings per manufacturer guidance to avoid overtightening.
• Inspect tubing ends for damage and cut squarely if needed for a proper seal.
• After installation, restore water and power, then check the connection carefully for leaks.

This drain tube routes wastewater from the appliance to the drain system, restoring proper drainage and preventing leaks or pooling. It's a direct-fit replacement designed to match the original drain path and connections. What it does

• Carries wastewater from the appliance pump to the household drain or disposal.
• Helps stop leaks or puddling caused by cracked, kinked, or clogged tubing.
• Restores normal drain cycles when a damaged tube prevents water removal.
• Prevents backflow when installed with proper routing and clamps.

• Disconnect power and turn off the water supply before starting any repair.
• Verify the tube routing and clamp positions match the original to avoid kinks and siphoning.
• Use proper clamps or fittings; tighten securely but avoid over-tightening which can damage the tube.

This replacement drain tube directs discharged water from the appliance to the household drain, helping restore proper drainage and reduce the risk of leaks. Designed to match OEM fit and routing for straightforward replacement. What it does:

• Channels drained water away from the appliance to prevent pooling and leaks
• Replaces cracked, split, or collapsed tubing that causes slow or no drainage
• Restores proper flow when water backs up or drains intermittently
• Works with factory clamps and fittings to maintain a secure seal

• Disconnect power and shut off water supply before beginning service
• Inspect surrounding fittings and clamps; replace any damaged hardware for a reliable seal
• Follow the appliance service manual for correct routing and clamp locations
• If you smell gas or detect significant water damage, stop.

The DRAIN TUBE is an OEM part specifically engineered for Whirlpool refrigerators. This essential component plays a crucial role in efficiently removing excess water or condensation from the refrigerator. Its precise design and compatibility ensure proper fitting and functionality within the appliance, preventing moisture buildup and potential water damage.

A damaged or clogged drain tube can result in issues related to excess moisture within the refrigerator. Causes of a malfunctioning drain tube might include blockages due to debris accumulation, physical damage, or wear and tear over time, leading to inadequate drainage or water pooling.

Symptoms of a faulty DRAIN TUBE may include:

• Water pooling or leakage inside the refrigerator
• Excessive condensation or moisture buildup
• Inadequate drainage resulting in water accumulation in the refrigerator

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

The Water Line is an OEM part for Whirlpool refrigerators. As a component of the refrigerator's internal plumbing system, this water line connects the water filter housing to either the ice maker or water dispenser valve. 

Causes of a bad water line can include kinks, cracks or splits developing over time from normal use and vibration inside the refrigerator walls. Mineral deposits may also cause restrictive buildup within the line.  

Symptoms of water line issues include:

• Slow or interrupted water/ice production  
• Water leaks near the connections
• Mineral/foreign debris appearing in ice or dispensed water
• Water filter or valve malfunctions

This OEM replacement line is compatible with many Whirlpool, Kenmore, KitchenAid and other refrigerator brands.

The Water Supply Tube is an OEM component specifically designed for connecting Whirlpool brand dishwashers to home plumbing systems. It transports water into dishwashers for cleaning and rinsing cycles.  

Potential causes of a problematic supply tube include mineral deposits reducing flow or small punctures from prolonged vibrations.

Symptoms of a faulty water supply tube include:

• Water leaks inside or underneath the dishwasher
• Inadequate water pressure impacting clean performance

Compatible models include some brands produced by KitchenAid, Maytag, and Kenmore.

This door waterline is the replacement tube that routes potable water through the refrigerator door to the dispenser/ice system, restoring reliable water flow and preventing door-area leaks. What it does

• Carries water from the refrigerator cabinet to the dispenser/ice door assembly.
• Replaces cracked, kinked, or clogged tubing that can reduce dispenser flow or stop water delivery.
• Stops leaks that originate inside or at the door hinge area when the original line is damaged.
• Restores proper water supply to ice makers and chilled water dispensers that draw through the door.

• Disconnect power and shut off the water supply before starting replacement.
• Inspect and, if needed, replace any associated quick-connect fittings or O-rings to ensure a watertight seal.
• Avoid sharp bends or kinks when routing the new tube through the door hinge area.
• After installation, turn the water back on and check all connections carefully for leaks.

This hose runs from water valve to the inlet on the side of the tank.