Kitchenaid Range Parts

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

I first diagnosed the problem by replacing the burner control (Infinite switch) with one from a smaller burner (one that I knew worked fine). That seemed to solve the problem. I ordered the correct control for the big burner on Saturday night, it arrived Tuesday and installed it in less than 10 minutes using only a Phillips screwdriver. Remember to unplug the stove before performing any service. Take this time to clean around and under the stove. (You know it needs it!) Read more

Ordered the part, which was easy and smooth. Watched you tube video on how to repair. Took me 15 minutes. Easy as it could be. Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Ordered new drip pans from Appliance Parts Pros, hoping they'd fit perfectly...and THEY DID! We are so happy with them. The ones at other places didn't. Read more

I replaced all 3 remaining burner controls because they were all original (mid 1970s GE electric range w/coil burners), and one of the controls occasionally made arcing sounds when cycling the burner on and off. If a control is making odd noises - more than just a quiet metallic clicking as it cycles - it should be replaced. I'm assuming you have experience with the tools needed and can do simple mechanical assembly or disassembly, but have not previously worked with electrical equipment of... Read more

First, don't self clean your oven before the holidays. In fact, read up on what damage the self cleaning feature can do to your oven. How did I fix it, I went on line and saw the comments of appliancepartspros.com. I figured out that it was the thermal fuse that probably went wrong since my oven just went lights out after the cleaning. My oven is a Kitchenaid model # KEBS179BSSOO. The part for this model is AP6022801 or WPW10545255. I spoke with technical support but I still had questions. I... Read more

After researching the problem, I ordered a new cooling fan. My "fix-it" guy winds up in the ICU for 3 weeks! So...YouTube here I come. It appeared pretty simple in video form, except the video wasn't of my stove. All in all, what looked like no more than a 6 screw removal, turned into tearing 1/2 the stove apart. Still, only took about 2 hours start to finish. Best lesson learned, turn off the energy efficiency mode!!! Read more

Replaced the blown heating element. I also only to be on the safe side, replaced the over temp sensor. I checked it with the meter when I pulled it out and it was ok. Tested ok. Thank you very much for the less than 2 day delivery on the part. Read more

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

Replaced the burner. Read more

The drip pans I ordered fit my stove perfectly. I was extremely happy. I had tried drip pans from Wal Mart and Lowe's and they wouldn't sit right in the stove. Read more

• Little to no heat when broiling
• Element will not heat

Found a real cool Youtube video by AppliancePartsPro.com. I watched it and learned how easy it was to unhook and replace the part with proper care and precautions. It even included tips on critical steps so the wires won't slip back inside the hole and save you from hours of possible mistake. Then I ordered the part. It came the day after, then I replaced the part, meaning, I DID THE WORK! (My wife was so impressed- lol) Easy as pie... but we made and had a much nicer roast the day after.... Read more

• Door won't open after self cleaning cycle
• Element will not heat
• Little to no heat when baking
• Won't start

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

• Little to no heat when baking

First I removed the (3) wire shelves. Removed the bottom cover by removing the (2) screws in the back. This exposed the oven element. Removed the (2) screws holding the mounting bracket on the front of the element then removed the (2) screws on the silver bracket that holds the back of the element. I carefully pulled the element forward which pulls it out of the back of the oven. I pulled slightly on the (2) wires attached to the element in order to get a small amount of slack to remove them... Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more