Kitchenaid Refrigerator Parts

• Clicking sound
• Won't start
• Freezer section too warm
• Fridge too warm

Removed back cover and installed new start device. Plugged in refridgerator and it runs like new. Read more

Door gasket was easy to remove and reinstall. Original gasket was penetrated while cleaning food stuff from folds in the seal below the frig doors. (Gasket is very fragile so don't try to expand the folds while cleaning. I used my finger and a paper towel but in hindsight should have used a Q-Tip. Also, when installing the new gasket you have to be sure the seam folds over the edge of the door and doesn't get caught underneath. Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

The rubber seal/gasket was torn on our KitchenAid refrigerator right side door. I purchased the replacement and followed the directions/recommendations of how to prepare the new gasket for installation. When it's removed from the shipping box, it does have wrinkles and preparing it is a must. I set it out on our tile floor and then used a heat gun (low setting) to warm it up and massage it. It took me about 15 minutes, stopping and restarting as I let the rubber come back to it's desired shape.... Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more

The replacement drawer arrived the day after I ordered it. I took the old drawer out, slid the new one in, and we were back in business. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

• Ice maker won't dispense ice
• Ice maker not making ice

After finding out the cost that we would have to pay for the repair locally, I went to Appliance parts pro.com. with the intention of finding out the cost for parts. We had been quoted $100 for the first hour which included repair if it could be done under the first hour plus parts. And they added that the typical repair for the ice maker was between $200 and $500. Fortunately we are very organized and had the original paperwork of the refrigerator which has all parts and numbers for the... Read more

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

• Ice maker dispenses too little ice
• Not dispensing water
• Touchpad does not respond
• Leaking

I'm such a pro, I figured I needed a new hose for my water dispenser so I ordered it. When it arrived I called my handyman. He told me I did not need a hose I needed A cartridge. So I had to return the hose and order the cartridge! Your company was so cooperative and made the return so easy Thank you! Next time I call the handyman first! Read more

• Fridge too cold
• Freezer too cold
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

After ordering the part, I first watched the video several times. Then I placed my phone on my workspace so that I could start and stop the video when following the step-by-step instructions. Then I shut down the refrigerator circuit breaker while I removed the ice container and full ice maker components. I then closed the refrigerator doors to keep the cold air in. I kept starting and stopping the video as I went, as I unplugged wiring components, connection jumpers, the ice maker shutoff... Read more

First Problem - WATER INLET VALVE - After having problems with ice maker not making ice, I troubleshot and replaced the water inlet valve. Video and instructions were excellent. With 16 year old fridge, the water lines had compression fittings in the old valve, so had to cut the fittings off with a razor blade to allow the lines to insert into the new valve press-in type fittings. Worked great / no leaks at the new valve. But, new leaks occurred at the water filter housing spraying down into... Read more