Maytag Bracket & Flange

Right side mount

Left side mount

This mounting bracket secures appliance panels and components to the cabinet, restoring proper alignment and reducing noise from loose parts. A small, direct-replacement part used where factory brackets have cracked or worn. What it does:

• Provides a secure mounting point for panels, trim, or internal components
• Prevents rattling, vibration noise, and misaligned doors or panels
• Restores correct fit where original bracket is broken, bent, or missing
• Keeps attached components stable during normal use

• One mounting bracket

• Disconnect power and water before starting any repair
• Remove surrounding panels or trim for access; keep fasteners for reassembly
• Use correct-size screwdriver or socket; avoid over-tightening to prevent cracking
• If adjacent parts are damaged, inspect and replace as needed for a secure fit

This mounting bracket secures internal components in place to keep your appliance stable and operating quietly. It replaces a worn, bent, or broken bracket to restore proper alignment and prevent loose or rattling parts. What it does:

• Provides a stable mounting point for panels, assemblies, or hardware
• Keeps connected components aligned to prevent rubbing or vibration
• Stops noises caused by loose or shifting internal parts
• Restores proper fit when an old bracket is bent, cracked, or missing

• Install with appliance unplugged or power disconnected to avoid shock
• Verify bracket orientation using the appliance's service diagram before fastening
• Use appropriate screws/fasteners and torque to avoid stripping or distortion

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This small anchor tip is a plastic mounting retainer designed to secure a component in place on compatible Whirlpool appliances. It provides a simple, low-profile hold so panels or wiring stay seated and aligned during normal use. What it does:

• Acts as a push-in retainer to hold a panel, trim piece, or small harness securely
• Keeps parts aligned to prevent rubbing, vibration noise, or loose panels
• Helps maintain proper fit between joined components after reassembly
• Commonly replaced when the original clip is worn, cracked, or broken

• One anchor tip mounting retainer

• Remove power and unplug the appliance before beginning any repair
• Typically installs by pushing into a pre-drilled hole until it snaps into place; may require a small flat tool for removal
• Inspect surrounding holes and mating parts; replace any damaged clips to ensure a secure fit

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This bracket assembly secures a switch and thermal fuse used to control power and protect the appliance from overheating. It replaces a worn or failed mounting assembly to restore proper electrical safety and switch function. What it does:

• Holds the switch and thermal fuse in the correct position for reliable operation
• Allows the switch to detect door/cover position or user inputs (safe, common symptom: appliance won't start or respond)
• Provides thermal-fuse protection when overheating or overcurrent interrupts normal operation (safe symptom: appliance stops mid-cycle)
• Restores secure electrical connections when the original bracket is cracked or terminals are loose

• Always disconnect power (unplug or shut off breaker) before starting work
• Basic hand tools required; follow the appliance's service manual for exact steps
• Inspect wiring and connectors for heat damage; replace if compromised

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket

This right-side basket cradle secures and supports a dishwasher rack so it rolls and nests correctly. It replaces worn or broken cradles to restore smooth rack movement and stable loading in the dishwasher. What it does:

• Holds the right side of the upper/lower basket in place and guides rack travel
• Restores proper alignment when racks tilt, wobble, or catch during sliding
• Helps prevent rack detachment or uneven loading caused by a broken cradle
• Works with the existing rack hardware and rollers to maintain normal operation

• Designed for straightforward replacement; remove the rack to access the cradle
• Inspect adjacent rollers and clips while replacing; replace any damaged hardware
• Use basic hand tools; disconnect power only if working near electrical components
• Dispose of damaged pieces and package new part per local regulations

This bracket is a factory-design mounting support that secures internal components in place for stable operation and alignment. It helps keep parts seated correctly to reduce noise and prevent component movement. What it does:

• Provides structural support for internal assemblies and panels
• Holds components in correct alignment to maintain proper operation
• Helps reduce rattling or vibration caused by loose parts
• Compatible where the OEM bracket W10174827 is specified

• Disconnect power to the appliance before starting any repair
• Use the correct fasteners and torque as specified by the manufacturer
• Wear safety gloves and eye protection to avoid cuts on sharp edges

This mounting bracket secures internal components to the appliance chassis to keep parts aligned and reduce movement during operation. It restores stable support so attached parts function reliably and quietly. What it does:

• Secures a component or assembly to the appliance frame to prevent shifting or sagging
• Maintains proper alignment of parts for reliable operation
• Helps reduce vibration and noise caused by loose or unsupported components
• Worn or broken brackets can cause rattling, misalignment, or intermittent part failures

• One mounting bracket

• Disconnect power before servicing to avoid electrical shock
• Use appropriate hand tools; keep fasteners for reinstallation unless new ones are specified
• Inspect surrounding components and mounting hardware; replace any stripped or damaged screws

This glass mounting bracket secures the oven door glass to the door frame, restoring a stable, properly aligned door and helping prevent rattling or loose glass. Designed to replace a worn, broken, or missing bracket. What it does:

• Holds the oven door glass in place so the door closes and seals correctly
• Prevents glass from shifting, rattling, or coming loose during use
• Restores proper alignment after a cracked, bent, or missing bracket
• Works with the door assembly to maintain safe, reliable operation

• Disconnect power to the appliance before beginning any repair; allow surfaces to cool.
• Handle glass carefully and wear cut-resistant gloves and eye protection.
• Replacement typically requires partial door disassembly; keep fasteners organized for reassembly.
• Tighten fasteners securely but avoid over-torquing; inspect surrounding clips and gaskets while installing.