Maytag Dishwasher Parts

Restore safe, smooth door operation with this dishwasher door spring. It counterbalances the door's weight so it opens and closes in a controlled way, preventing a sudden drop when the original spring breaks or fatigues.

• Provides the tension that counterbalances the dishwasher door through the hinge mechanism
• Helps prevent the door from slamming open or feeling unusually heavy
• Restores smooth, even door movement side-to-side
• Typical symptoms: door drops quickly, feels heavier than normal, uneven motion, or a visibly broken/stretched spring

• Disconnect power and shut off water before servicing
• Remove the toe/kick panel to access the hinge area
• Support the door, then move it slightly to relieve tension before unhooking the old spring
• Attach the new spring between the frame anchor and hinge arm; if your model uses two springs, replace both sides for even tension

This cup shelf clip secures the dishwasher's fold-down cup shelf to the upper rack. Replacing a cracked or missing clip restores a stable shelf so cups and small items stay organized throughout the wash cycle.

• Fastens the cup shelf to the upper rack wire to prevent wobble or detachment
• Helps the shelf pivot and lock properly when raised or lowered
• Typical symptoms: shelf hangs loose, falls off, won't stay in position, or the original clip is broken/missing

• Open the door and fully extend the upper rack; remove the rack if needed for access
• Squeeze the old clip's tabs to release and lift it off the rack wire or shelf
• Align the new clip on the rack wire and press until it snaps securely into place
• Verify the shelf moves and locks correctly before running a cycle

This miniature door switch is the snap-action interlock that tells the appliance when the door is closed. Replacing a worn or sticking switch restores reliable start/stop and proper door-status sensing for safe, consistent operation. What it does:

• Acts as the latch/interlock sensor for door open/closed status
• Signals the control to allow or prevent operation based on door position
• Typical symptoms include: won't start or shows a door message, stops when the door is bumped, or light/fan behavior doesn't match door position

• 1 miniature door switch

• Disconnect power before servicing. If working on a microwave, high voltage may be present even when unplugged—properly discharge the capacitor.
• Access the latch/interlock area; note wire positions and transfer one lead at a time to the new switch.
• Use a multimeter to confirm the switch changes continuity when pressed before reassembly.

Bushing, Door spring

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

This dishrack replaces a damaged or rusted rack in your dishwasher. Restoring a true-to-spec rack keeps plates, bowls, and cookware secure and properly spaced so the machine can clean effectively and the rack moves smoothly on its tracks. What it does:

• Organizes and supports dishes and cookware during wash and dry cycles
• Maintains proper spacing for spray coverage and drainage
• Interfaces with the rail system to slide in and out when paired with the correct rollers/stops for your model
• Common symptoms: rusted or broken tines, deteriorated rack coating, misshapen frame, rack falling off tracks or not sliding properly

• 1 dishrack

• Disconnect power to the dishwasher before servicing
• Open the door; pull the existing rack out. For upper racks, release/remove rack stops or end caps; for lower racks, lift straight out
• Transfer any reusable components (rollers, clips, fold-down tines, silverware basket) from the old rack
• Slide the new rack onto the rails and reinstall stops; verify smooth travel before running a cycle

Included with nut.

Color: light gray. Measures about 3 inches high by 6 inches deep.

Right Side. For left side use part number WPW10251050.

This replacement upper spray arm restores strong spray coverage to the upper wash level of your dishwasher. It channels water through its jets and spins under pressure to help deliver consistently clean dishes on the top rack.

• Directs pressurized wash water to the upper wash level for thorough cleaning
• Rotates under water pressure for even spray coverage
• Helps clear food soils and detergent residue from dishes and glasses
• Common symptoms: poor cleaning on the upper rack, spray arm not spinning, clogged or cracked arm

• Disconnect power and shut off the water supply before servicing
• Open the dishwasher; remove the upper rack if needed for access
• Release or unthread the retainer and pull the old arm straight off; clear debris from the hub/feed port
• Seat the new arm and secure the retainer hand-tight; ensure the arm spins freely and run a test cycle

Color: light gray. Measures about a 1/2 inch high by 4 inches deep.

This overfill control float assembly sits in the dishwasher tub and rises with the water level. It works with the float switch to shut off the inlet valve, helping prevent overfilling and potential leaks.

• Rises with the water level to engage the float switch and stop water flow
• Helps protect against tub overfill and floor leaks during the fill cycle
• Replace if the float is missing, warped, stuck, or doesn't move freely
• Symptoms can include continuous filling/overfilling, water spilling from the door, or no fill if the float is stuck in the up position

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; lift the old float straight up from the tub opening
• Clear any debris from the float well so the new float moves freely
• After reassembly, start a fill to ensure the float rises and water shuts off

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

Dishwasher silverware basket includes both halves. Color: gray. Measures about 8 inches wide by 9-1/2 inches high by 12 inches deep.

The Door Latch Handle is an OEM replacement part for Whirlpool dishwashers. It is used to release the door latch and open the dishwasher door. This handle enables you to disengage the latch, allowing the door to open smoothly.

If the handle is damaged, it may become challenging to release the latch, making it difficult or impossible to open the door. Over time, this component can wear out due to frequent use or break due to accidental mishandling.

Color: White

Symptoms of a damaged door latch handle include:

• Difficulty opening the dishwasher door
• The door not opening at all
• Handle feeling loose or unresponsive

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control panel replaces the front console that houses the buttons and indicator lights on your dishwasher. It restores a clean look and responsive inputs so you can select options and start cycles reliably again.

• Provides the user interface for cycle selection, Start/Cancel, and options
• Sends keypad inputs to the main control board for proper operation
• Displays status/option indicators where applicable
• Replaces cracked, faded, or unresponsive consoles to improve usability

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to release the console from the door
• Support the wiring; transfer any clips/trim and reuse existing hardware as required
• Avoid pinching the ribbon cable and verify button function before final reassembly