Maytag Latch, Catch, Lock Parts

This latch secures the door closed and signals the control that it's safe to run. Replace a worn or broken latch to restore solid door engagement and reliable operation.

• Engages the strike to keep the door firmly closed during use
• Provides the "door closed" signal to allow cycles to start
• Common symptoms: door won't latch or pops open; must hold door shut to run; "door open" message or won't start with door closed
• Helps ensure safe, consistent operation by maintaining proper door engagement

• Disconnect power before servicing; the appliance is fully de-energized
• Access the latch from the door/console area; note fastener and wiring locations for reassembly
• Inspect/align the door strike so the latch engages smoothly
• After installation, close the door and run a short cycle to confirm proper engagement and operation

This door catch assembly secures the door by engaging the mating latch or strike, keeping it firmly closed for proper operation and safety. Replace a worn or broken catch to restore reliable door closure and consistent performance. What it does

• Engages the door latch/strike to hold the door closed during use
• Helps maintain proper door alignment and contact with seals/interlocks
• Restores a positive latch feel and consistent closure
• Common signs of wear: door won't latch or pops open, must be slammed to close, visible damage to catch tabs

• One door catch assembly

• Unplug the appliance or switch off power at the breaker before servicing; for gas appliances, shut off the gas supply
• Open the door, access the catch at the cabinet/frame, and remove retaining screws or clips
• Transfer any reusable hardware from the original part and install the new catch
• Verify smooth latch engagement and door alignment before restoring power

This door strike is the catch the latch engages to hold the oven door closed. It restores a firm, aligned close so heat stays in and the appliance can detect a fully shut door for normal operation.

• Aligns with the latch to keep the door closed and sealed properly
• Provides the catch point required for latch/lock engagement
• Wear, bending, or breakage can cause a loose door, heat escaping, or an oven light that won't turn off
• Prevents self-clean or other cycles that require a fully closed/locked door from starting

• Disconnect power at the breaker; if gas, shut off the gas supply. Allow the appliance to cool completely
• Typically mounts to the door or cabinet frame with screws; transfer and reuse existing hardware
• Position and tighten evenly so the latch engages smoothly; minor alignment adjustments may be needed
• After installation, verify the door closes fully, seals well, and the light turns off

Color: Black

This Door Catch Bezel, in white, is an OEM part for Whirlpool dryers. It secures the dryer door, making sure it remains closed during operation. Crafted precisely to fit compatible dryer models, this bezel guarantees a secure and snug fit.

What causes a bad part:
The Door Catch Bezel might deteriorate due to frequent use, exposure to heat, or physical strain during the opening and closing of the dryer door. Additionally, prolonged exposure to cleaning agents or moisture can contribute to its degradation.

Symptoms for a bad part:

• Difficulty in securely closing the dryer door
• Loose or shaky door closure
• Visible damage or cracks on the bezel

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This bezel is a trim piece that finishes and protects the opening around a control or feature on the appliance's panel. Replacing a cracked or missing bezel restores a clean look and helps the mating control sit securely and operate properly.

• Frames the control or opening and covers raw edges for a finished appearance
• Helps keep the associated knob/button or trim aligned and seated
• Shields internal components from dust, splashes, and minor impacts
• Replace if cracked, warped, loose, or missing; symptoms can include a wobbly control, visible gaps, or cosmetic damage

• Disconnect power at the breaker before servicing; allow any hot surfaces to cool
• If applicable, pull off the knob or remove adjacent trim to access the bezel
• Release locking tabs or remove mounting screws carefully to avoid scratching the panel
• Align the new bezel with tabs/orientation marks and snap or fasten into place; reinstall parts and test

This door latch keeps the door securely closed and engages the door switch/interlock so the appliance operates as designed. Replacing a worn or broken latch helps resolve door-related errors and restores reliable, safe operation.

• Secures the door against the strike for proper closure and alignment
• Actuates the door switch/interlock so controls recognize a closed door
• Helps prevent operation when the door is open or not fully latched
• Common symptoms: door won't latch or stay closed; unit won't start or shows a "door/open-close" message; broken or loose latch hook

• Disconnect power before servicing; use proper PPE and beware of sharp edges
• Access the latch through the door panel/trim as applicable; use non-marring tools to avoid damage
• Transfer any reusable clips/springs from the old latch to the new part
• After installation, verify smooth door closure and that the control detects the door as closed

This lock cam is a small actuator that drives the appliance's door-lock mechanism. It translates the lock actuator's movement into a positive latch, helping the door lock securely when required and release correctly so cycles start and finish properly.

• Interfaces with the lock actuator and latch to engage and release the lock
• Wear, cracking, or rounding can cause the lock not to engage or to stick
• Common symptoms include a door/lid that won't lock or unlock, loose lock lever, clicking without latching, or door/lock-related error messages
• Restores proper linkage travel and switch actuation when the original cam is worn or damaged

• Disconnect power to the appliance before servicing
• Access the lock mechanism per your model; note the cam's orientation and any springs/linkages
• Install the new cam fully seated and ensure it engages the actuator and latch smoothly
• Reassemble, restore power, and test lock operation

The Door Strike is an OEM replacement part for Whirlpool dryers. This component ensures the dryer door securely latches, enabling the appliance to operate and preventing it from running with the door ajar. It works in conjunction with the door catch to maintain a proper seal during drying cycles.

Symptoms of a bad Door Strike include:

• The dryer door not latching or staying closed
• The dryer not starting due to the door remaining open
• The door popping open during operation
• Visible wear, bending, or damage to the strike

Causes of a failing Door Strike can include regular wear and tear, misalignment from improper use, or damage from slamming the door. Replacing a faulty strike ensures the dryer operates safely and efficiently.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This in the male piece on the front panel. For the female piece on the door order WPW10111905.

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation

This is the keyed lock insert for select appliance doors. It lets you lock or unlock the door to secure contents and prevent unintended opening.

• Engages the door's lock mechanism to secure or release the door
• Helpful when the door won't lock/unlock or the original key is lost
• Restores proper locking function without replacing the whole lock assembly

• Unplug the appliance before service
• Verify the key profile matches your existing lock before use
• Insert fully and turn gently; do not force if resistance is felt
• Keep a spare key in a safe location away from the appliance

This lid switch actuator engages the washer's safety switch when the lid is closed so cycles can start and spin as designed. Replace a broken or missing actuator to restore proper lid switch engagement and reliable operation.

• Engages the lid switch when the lid is closed to enable agitation and spin
• A worn, cracked, or missing actuator can cause the washer not to start or to stop before spin
• Intermittent operation that changes when pressing on the lid often indicates misalignment
• Lack of an audible "click" from the lid switch can point to a faulty actuator or alignment

• Disconnect power before servicing; do not work on a live appliance
• Access the lid/switch area per your model's service procedure
• Remove the damaged actuator and install the new part, securing as designed
• Before reassembly, close the lid to ensure the switch clicks and engages properly

Replacement lid strike assembly that secures the washer lid so the machine can operate reliably. Restores proper lid engagement to help prevent the washer from stopping mid-cycle or the lid from coming unsecured during use. What it does:

• Engages with the lid latch to hold the lid closed during wash and spin cycles
• Restores proper lid alignment and secure closure when the original strike is worn, broken, or missing
• Common repair for symptoms like the lid not staying latched, the washer refusing to start, or a rattling/slipping lid

• Disconnect power before servicing the washer
• Typically installs at the lid/hinge area; may require removing the top panel or console for access
• Use basic hand tools and take care around springs and hinges to avoid injury

This strike is the catch point the latch grabs to keep the appliance door securely closed during operation. Replacing a worn or broken strike restores reliable latching so cycles can start and run properly. What it does:

• Engages with the door latch to hold the door closed during use
• Helps ensure the control senses the door is closed
• Maintains proper alignment for smooth, consistent latching
• Typical symptoms: door won't latch or stay closed, "door open" message, cycle won't start, intermittent operation when the door is moved

• 1 door strike

• Disconnect power to the appliance before servicing
• Remove the existing strike and retain mounting hardware if reusable
• Position and secure the new strike; adjust so the latch engages without forcing
• Close and test the door for smooth engagement before running a cycle

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle