Maytag Panel Parts

This is the top panel that covers the upper portion of the washing machine cabinet, forming the main lid surface of the unit. It provides structural support and protects internal components from dust and moisture. Replace this panel if it is dented, rusted, cracked, or damaged - note that installation may require welding depending on how the original panel was attached.

Exterior upper cover panel for washers. Restores a finished look and protects internal components. Replace if cracked, dented, or damaged from impact.

Heat deflector shield for wall ovens. Directs heat away from sensitive components inside the oven cavity. Replace if torn, warped, or missing.

Control panel for dryers and laundry centers. Replaces cracked, broken, or damaged panels on the front of your unit. Restores appearance and function.

Trim kit for installing a custom wood panel on your dishwasher door. Replaces broken, cracked, or missing trim pieces. Does not include wood panel.

Control panel for dryers. Installs on the front of the unit housing the display and buttons. Replace if cracked, damaged, or faded from wear and age.

Replace your laundry center's damaged or dented top panel. This cover installs on the washer section and restores appearance after moving damage or wear.

White transition panel for laundry centers. Covers the gap between washer and dryer units. Replace if cracked, discolored, or missing.

Replacement top-load washer lid. Covers the wash basket and prevents water splashing. Order if your existing lid is cracked, broken, or missing.

This rear panel replaces the back cabinet cover on compatible Whirlpool dryers, protecting internal components and helping direct vent airflow. It restores a secure, finished exterior and keeps wiring and controls shielded. What it does:

• Covers and protects the dryer's internal components at the rear, including wiring and control assemblies
• Helps maintain proper venting path and airflow by providing the correct rear opening and mounting surface
• Prevents debris, pets, and accidental contact with internal parts
• Stops rattling or flexing caused by a bent or damaged back panel

• Disconnect power (and gas supply on gas models) before starting any repair
• Remove the dryer from the wall and disconnect the vent to access and replace the rear panel
• Use appropriate hand tools to remove and reinstall mounting screws; retain hardware if reusing
• Handle edges carefully to avoid cuts; secure all fasteners before returning dryer to service

This retainer is a small mounting clip that keeps a nearby component held securely in place, helping prevent rattles and misalignment for reliable appliance operation. Install restores proper positioning of the secured part. What it does

• Holds a component or assembly in its intended position to prevent movement or vibration
• Common symptom: loose or rattling parts near the retainer location
• Common symptom: component shifts or comes partially detached during operation
• Works as a replacement for a cracked, broken, or missing retainer that fails to secure the part

• One retainer

• Disconnect power (unplug appliance or switch off circuit breaker) before beginning any repair
• Accessing the retainer may require removing a panel or adjacent parts; keep fasteners organized
• Use basic hand tools; avoid forcing parts to prevent damage to surrounding components

Replaces cracked, broken, or missing lower access panel on your dishwasher. Covers the base opening for a finished look and shields internal parts.

White front access panel for dishwasher door. Replace worn, discolored, or damaged panels to restore your dishwasher's appearance. Direct fit installation.

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care