Maytag Washer Control Board

This motor control board regulates and powers the washer's drive motor, coordinating speed, direction, and spin. Replacing a failed module can restore proper tumbling/spinning performance and resolve common motor-related faults.

• Supplies variable-speed power to the drive motor for wash and spin
• Monitors motor feedback to maintain correct speed and direction
• Communicates with the main control to carry out cycle commands
• Common symptoms: no tumble or spin, erratic/incomplete spin, cycle stops with motor/communication errors

• Disconnect power before servicing; verify power is off
• Use ESD protection and handle the board by the edges
• Access the board inside the cabinet; move connectors one at a time and seat them fully
• Inspect the motor and wiring harness for shorts or damage before restoring power

This washer timer regulates the order and length of each wash, rinse, and spin stage by sending power to the right components at the right time. Replacing a failed timer restores proper cycle advancement and dependable operation.

• Sequences wash, rinse, drain, and spin through the complete cycle
• Directs power to the drive motor, water inlet valves, and drain pump as programmed
• Common symptoms it can help resolve: cycle won't advance, stops mid-cycle, runs longer than expected, or is stuck on one setting
• Mounts in the control console and interfaces with the cycle selector knob

• Disconnect power before servicing; verify controls are off
• Access the console; photograph or label wiring, then transfer wires to the new timer one at a time
• Secure the timer, reassemble the console, and align the selector/indicator
• Run a short test cycle to confirm proper advancement; check the lid switch and wiring

Restore reliable operation with this electronic control board. Acting as the appliance's central processor, it interprets user/sensor inputs and switches components to run the selected cycle accurately and consistently. What it does

• Controls cycle timing and powers components to execute selected programs
• Communicates with sensors and the user interface to carry out settings
• Typical failure symptoms: won't start or respond to controls, stops mid-cycle, won't advance through a cycle, or displays error codes
• Can cause intermittent power or unresponsive controls when faulty

• 1 electronic control board

• Disconnect electrical power at the breaker before servicing; verify no power is present
• Handle the board by the edges and use anti-static protection
• Photograph wiring and move connectors one at a time to matching terminals; transfer any reusable brackets/shields from the original part if applicable
• After installation, restore power and run a test/diagnostic cycle per the tech sheet for your model to verify operation

Restore accurate cycle control with this washer timer. It sequences power to the drive motor, pump, and water inlet valves so the machine fills, washes, drains, and spins at the proper times.

• Advances the cycle through fill, wash, rinse, drain, and spin stages
• Sends power to the motor, pump, and inlet valves in the correct order and duration
• Safe symptoms: washer won't start, won't advance, stops mid-cycle, runs indefinitely, or skips rinse/spin
• Helps when cycles stall or the dial turns without moving the cycle forward

• Unplug the washer before servicing
• Open the control console to access the timer; note or photograph wiring
• Transfer wires one at a time to matching terminals on the new timer
• Reuse your existing knob/dial and mounting hardware; align the timer shaft before tightening

This is a washing machine timer manufactured by Whirlpool.The timer controls the duration of the selected washer cycles by controlling electrical components within the washing machine. Timers are subject to wear and tear or deterioration over time, which might cause the user to notice longer or shorter washing machine cycles than usual. Unplug the washing machine from power and disconnect it from the water source before attempting to replace the timer. Work gloves can be worn to prevent the risk of injury to the hands. This is an authentic OEM part and, as such, is sold individually and made from durable, high-quality, non-corrosive materials to ensure high quality. This timer is compatible with different washing machines manufactured by Whirlpool, Maytag, Jenn-Air, Amana, and other brands.

This washer timer is the mechanical cycle controller that sequences power to the motor, pump, and water valves. Replacing a worn timer restores proper cycle advancement so the washer starts, progresses, and stops at the correct times.

• Controls the length and order of wash, rinse, and spin cycles
• Directs power to the drive motor, drain pump, and inlet valves as the cam advances
• Advances the cycle automatically; interfaces with the timer knob for manual selection
• Failure symptoms include cycles not advancing, stopping mid-cycle, skipping steps, or no start

• Disconnect power and turn off water supply before servicing
• Access the control panel; remove the knob/dial and mounting screws to release the timer
• Note wire positions or take a photo; transfer connectors one at a time to matching terminals
• Reinstall, secure the timer, and run a short test cycle to ensure proper advancement

This timer is the mechanical cycle controller for select top-load washers. It sequences power to the motor, water inlet valves, and drain pump so each step runs in the correct order and duration for consistent, reliable operation.

• Directs power to advance the washer through fill, wash/agitate, drain, and spin
• Restores proper cycle advancement when the washer stalls or skips steps
• Helps resolve symptoms like stopping mid-cycle or running indefinitely
• Can correct intermittent or erratic cycle timing/advancement issues

• Disconnect power before servicing; access the timer from the control console
• Transfer wires from the old timer to the new one, moving one connection at a time
• Reuse existing mounting hardware and control knob/dial as applicable
• Handle sharp cabinet edges and verify dial alignment before reassembly

This part is a moisture sensor control board that is used on dryer units. This component monitors the moisture levels within the dryer and adjusts the dry time during the automatic drying cycle. A new moisture sensor control board will be needed if the time is not advancing in the automatic drying cycle, even if it does advance in the timed dry cycle. Another sign is if the dryer continues to run after the clothing inside is dry. Unplug the dryer from its power source prior to replacing this component. The person performing this task may wish to wear work gloves to protect their hands.The moisture sensor control board is compatible with dryers that are manufactured by Kenmore, KitchenAid, Kenmore Elite, Whirlpool, Amana, Crosley, Maytag, Inglis, Sears Canada, Roper, and Sears. This part is sold individually and it is a genuine OEM replacement part that comes straight from the manufacturer.

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

This mechanical cycle timer controls the sequence and duration of washer operations. Replacing a failing timer restores proper advancement through fill, agitate, drain, and spin so cycles complete reliably with accurate timing. What it does:

• Advances the washer through each step by routing power to the water valves, motor, and drain pump at the correct times
• Sets the length of each stage for consistent operation
• Common failure signs: cycle won't advance or stops mid-cycle
• Timer knob doesn't move or must be jiggled to run
• Skips functions (no agitate, drain, or spin) while others still work

• 1 mechanical timer assembly

• Disconnect power before servicing; access the timer from the control console
• Take photos or label wires; transfer them to the new timer one at a time to maintain correct positions
• Reuse the existing knob and dial; align the timer shaft properly and secure the mounting screws
• After reassembly, run a short test cycle to ensure proper advancement

This electronic control board manages the appliance's control functions and user interface, restoring normal cycle selection and electronic operation when the original board fails. Designed as a direct replacement for the main control assembly. What it does:

• Receives user inputs and sends commands to start, stop, and change cycles
• Regulates timing and communication between sensors, motors, and valves
• Can correct problems like unresponsive controls, incorrect cycle operation, or display errors
• Helps the appliance run intended functions when the original board is faulty

• One electronic control board

• Disconnect power before servicing to avoid shock or damage
• Handle the board by edges and avoid static discharge; use ESD precautions if available
• Verify connector alignment and seating; do not force connectors
• Follow OEM disassembly/reassembly steps and test appliance after installation

The Washer Control Board is an OEM part for Whirlpool brand washers. This board is responsible for controlling all functions and cycles of the washing machine. It analyzes input from sensors and displays cycle status and diagnoses error codes.

Causes of a bad control board can include water damage over time, failure of electronic components due to normal wear and tear, or improper installation.  

Symptoms of a bad control board include:

• The washer fails to start or does not advance through cycles
• Error codes are frequently displayed  
• Certain cycles or options no longer function properly
• - The display is not illuminated or is glitchy

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This part is an control board that can be used as a replacement for a broken or malfunctioning control board in various washing machine models. This part ensures the washer functions, such as draining and filling, can be properly managed. In cases where the washer cannot be efficiently controlled, replacement will be immediately required. The control board will also need to be replaced if the user sees the F1 E1 error code. Before replacing this part, ensure the washing machine is unplugged from the power and water sources. Work gloves should be worn anytime a repair or replacement is attempted.This is a genuine OEM part made by Whirlpool and has been sourced directly from the manufacturer. This part is suitable for use on a variety of washing machine models that have been manufactured by Whirlpool, Maytag, Jenn-Air, and Amana. It is a genuine OEM part and thus is manufactured from high-quality, durable, non-corrosive materials and is only sold individually.

This replacement timer controls the sequence and duration of your washer's cycles, helping the machine advance smoothly through fill, wash, rinse, drain, and spin. Replacing a failing timer can restore consistent cycle progress and dependable operation.

• Controls timing and sequencing for fill, agitate, drain, and spin operations
• Switches power to the motor, pump, and water valves as each step advances
• Advances the cycle knob/dial through each phase
• Can also help with skipping rinse/spin or a dial that's hard to turn

What's included: 1 timer assembly Install notes:

• Disconnect power before servicing
• Remove the console/panel; pull off the knob and dial as needed to access the timer
• Transfer wires one at a time from the old timer to the new; mount and secure the timer
• Reassemble, restore power, and run a short cycle to verify operation

This electronic control board governs your appliance's cycles, timing, and user commands. A failed board can cause unresponsive controls or erratic behavior; replacing it restores reliable operation. What it does:

• Manages program logic and timing for selected cycles
• Routes power to components as programmed
• Interprets keypad/sensor inputs and updates the display
• Stores and communicates diagnostic fault codes
• Common failure symptoms: blank or unresponsive controls, won't start or complete cycles, random resets, error beeps/codes

What's included:

• Electronic control board

Install notes:

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD protection and handle the board by the edges only
• Photograph wiring and move connectors one-by-one to the new board, confirming keyed orientation
• Reuse existing mounting hardware as required; follow the tech sheet or included service instructions