Microwave Parts

This replacement motor restores reliable rotation to the component it drives, helping your appliance circulate air or operate as designed. Replacing a worn motor can resolve no-start conditions, loud operation, and weak performance.

• Provides the rotational drive for the attached component, enabling proper airflow or movement
• Common failure symptoms include humming without turning, intermittent operation, seized shaft, or grinding/squealing noises
• Visual signs like burned windings, cracked housing, or excessive shaft play also indicate replacement is needed

• Disconnect power to the appliance before servicing; allow any moving parts to stop completely
• Photograph or label wire positions and transfer them to the new motor one-for-one
• Reuse existing mounting hardware and verify the motor and attached wheel/blade spin freely without rubbing
• After installation, restore power and test operation before final reassembly

This turntable motor drives your microwave's glass tray, rotating food for more even heating. Replacing a failing motor restores proper tray movement and helps reduce cold spots during cooking. What it does:

• Rotates the glass tray via the turntable coupler during cook cycles
• Helps promote even heating by keeping food moving
• Addresses symptoms such as the tray not turning, intermittent rotation, or grinding/clicking noises from beneath the cavity
• Useful check: ensure the roller ring and coupler aren't damaged or obstructed

• 1 turntable motor

• Disconnect power; microwaves contain high-voltage components that can retain a charge
• Typically accessed from the unit's bottom panel; remove the cover to reach the motor
• Move the two wires and mounting screws from the old motor to the new one; align the shaft with the coupler
• After reassembly, confirm the tray sits correctly on the roller ring and spins freely

This replacement screw secures appliance components such as panels, brackets, and covers. Replace a missing or stripped fastener to restore a tight, rattle-free fit and proper alignment. What it does:

• Secures panels, brackets, trim, and internal assemblies in place
• Replaces lost, corroded, or stripped hardware
• Helps reduce vibration and rattling from loose components
• Maintains correct fit and alignment of covers and parts

• One screw

• Disconnect power before servicing; wear appropriate safety gear
• Match the screw to the original location; transfer any washers or clips from the old hardware
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair damaged receiving threads before installing the new fastener

This genuine replacement door handle restores a secure grip and smooth operation to your appliance door. It replaces a worn, cracked, or broken handle so you can open and close the door safely and comfortably. What it does:

• Provides a sturdy handhold for opening and closing the appliance door
• Replaces cracked, loose, or broken handles that cause difficulty operating the door
• Restores proper alignment and fit where the original handle has worn or failed
• Helps reduce accidental slippage or dropping of the door during use

• One door handle

• Handle requires basic hand tools for removal and installation; refer to your model's service instructions
• Keep the appliance unplugged or power disconnected when working near electrical components
• Tighten mounting fasteners securely but avoid over-torquing to prevent cracking
• If the handle mounts to an inner door panel or trim, support the door edge to avoid damage during installation

This holder nut assembly secures a component to the appliance frame, restoring proper mounting and reducing vibration or movement. Replace a damaged or missing holder nut to keep connected parts stable and functioning. What it does:

• Secures a component or assembly to the appliance frame or mounting bracket
• Prevents looseness, rattling, and misalignment caused by worn or missing mounting hardware
• Restores a safe, stable connection that helps maintain normal operation
• Matches OEM mounting geometry for a direct replacement when the original nut is damaged

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the mounting area by removing the appropriate panel or cover per your model's service instructions
• Start threads by hand to avoid cross-threading, then tighten with the correct tool; do not overtighten
• If any fasteners or nearby components are damaged, replace them as needed for a secure installation

This NTC thermistor is a temperature sensor that feeds real-time temperature data to the control. Replacing a failing sensor helps restore accurate temperature regulation, reduce nuisance shutdowns, and improve consistent cycle timing and performance.

• Monitors temperature by changing resistance as heat rises or falls
• Sends a signal to the electronic control to manage heating and fan operation
• A failed sensor can cause inaccurate temperatures, short/long cycles, or sensor-related error messages
• May prevent certain cycles from starting

• Disconnect power and allow the appliance to cool completely before servicing
• Note connector orientation and wire routing; take a photo for reference
• Install the sensor in the original location/clip and route wires away from hot or moving parts
• Restore power and run a test cycle to proper temperature response

Replacement fastener used to secure appliance components. If a screw is missing or damaged, panels and brackets can loosen or rattle. Installing a new screw restores a tight fit and helps keep parts properly aligned.

• Fastens panels, brackets, or internal components as designed for the model
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration/rattling and restores proper fit
• Maintains alignment and a secure assembly after service

• Disconnect power; shut off gas if applicable before servicing
• Support components while removing/installing fasteners
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace all required screws in a location for even clamping and proper fit

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This microwave thermostat is a temperature-sensitive safety switch that helps protect the unit from overheating. When the preset limit is reached, it interrupts power to the affected circuit to help prevent damage and erratic shutdowns.

• Monitors temperature at its mounting location and opens the circuit if overheating is detected
• Helps protect internal components from excessive heat
• Common symptoms of a failed thermostat include: unit shuts off during cooking, won't start until it cools down, or has no power/no heat due to an open safety
• Replace if the original tests open when it should be closed

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Microwaves contain a high-voltage capacitor that can retain a dangerous charge; only qualified persons should service and discharge the capacitor
• Note wire locations before removal and transfer connections firmly to the new thermostat
• Mount the thermostat securely and in the same position to ensure proper temperature sensing

This is a magnetron that is used on microwave ovens. The purpose of the magnetron is to provide the microwaves that actually cook the foot inside of the microwave oven. Use caution when replacing this part. High-voltage capacitors in microwaves can retain a deadly amount of electrical charge, even when they are unplugged.If the microwave begins making a buzzing noise and doesn't heat food properly, this part will need to be replaced. Use extreme caution when working with this appliance. Unplug the unit first.This particular magnetron is compatible with microwave ovens that are manufactured by the General Electric, Hotpoint, and Maytag brands. This part is sold individually and is sourced directly from the manufacturer as a genuine OEM part.

The Microwave Thermostat is an OEM part for GE Countertop Microwaves. It is a critical component that monitors the microwave's internal temperature to ensure safe operation. 

Causes of a bad thermostat can include failure of internal components due to prolonged heat exposure during cooking cycles over many years of use. Steam and splatters introduced into the microwave from heated foods can also damage sensors.

Symptoms of a bad thermostat include:

• Inability to heat or reheat foods adequately 
• Short cycling of the microwave interior lights 
• Erratic power levels during cook functions
• Overheating errors or shutoffs for safety

This replacement thermostat is also compatible with RCA and some Kenmore countertop microwave models.

This removable wire rack fits microwaves designed for rack use, creating a second cooking level. Replacing a missing, bent, or chipped rack restores safe operation and the intended capacity for multi-item reheating and cooking.

• Provides a stable second-level surface for cooking or reheating multiple items in compatible models
• Positions dishes at the proper height for rack-enabled functions
• Replace if missing, bent, rusted, or if damaged coating causes arcing/sparking
• Use only in microwaves designed for a rack; follow your Use & Care manual

• Disconnect power before servicing; allow the cavity to cool
• Insert the rack into the designated side-wall supports; ensure it is level and not touching cavity walls or the turntable
• Remove the rack for cycles that require single-level cooking if instructed by your manual
• Stop use if arcing occurs; inspect placement and rack condition before resuming

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

The Microwave Fuse Cartridge is an essential component for maintaining the safety and functionality of your microwave. This genuine OEM part is specifically designed to meet Samsung microwave standards, ensuring a reliable and secure fit. By replacing a faulty fuse cartridge with this high-quality part, you can restore your microwaveGÇÖs performance and prevent potential electrical issues. The Microwave Fuse Cartridge effectively safeguards your appliance from power surges and short circuits, providing peace of mind and enhancing the longevity of your microwave. Its easy installation process allows you to quickly get your appliance back in working order without the need for professional assistance. Compatible with a wide range of Samsung microwave models, this genuine OEM part guarantees optimal compatibility and performance. Choosing the Microwave Fuse Cartridge means investing in a durable and trustworthy solution that keeps your kitchen running smoothly and safely.

Color: White

This replacement screw secures appliance panels, brackets, or internal components to keep them tight and aligned. Replace a missing, stripped, or damaged fastener to restore a solid, rattle-free fit and reliable operation.

• Fastens parts to the cabinet or frame to prevent movement
• Replaces missing, stripped, or corroded hardware that can cause looseness, vibration, or noise
• Helps correct gaps or misalignment after service
• Maintains proper support for covers, trims, or brackets

• Disconnect power; shut off gas/water if applicable before servicing
• Match screw length and location to the original position
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace damaged clips/inserts before installing the new screw