Mtd Parts

Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.

Fix snow thrower auger that won't turn or spins slowly with a new auger belt. This rubber V-belt drives the auger rotation on two-stage models.

This is a wheeled string trimmer belt compatible with many brands. The belt's purpose is to drive the unit, transferring power from the engine to the cutting head. Over time, belts are subject to wear and tear, heat, and humidity. This can make the belt brittle and eventually it will snap. In other instances, belts will stretch after being used for long periods and need to be replaced. Replacing the belt is a simple process. Start with the engine off and the spark plug disconnected. Remove the screw holding the chassis cover in place and then the screws holding the debris shield. With the debris shield out of the way, the belt should be clearly visible. Remove the engine pulley, but make sure to note the pulley's position for replacement. Install the new belt and reassemble the trimmer. This part is a genuine OEM part sourced directly from the manufacturer and sold individually. This belt is compatible with Craftsman, Bolens, Remington, Ryobi, and Yard-Man brands.

Metal carriage bolt with round head and threaded shank for lawn mowers and snow blowers. Replaces broken or missing hardware during repairs or assembly.

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

This is a versatile screw designed with flanged hex head and double-lead threads. It is a high-low self-tapping screw with one thread that is high and the other low for easier penetration. The twin threads also reduce the amount of material displaced when the screw is driven into the material. This type of screw also creates a firmer grip. This screw can also be used to secure a newly installed front cover or grill. This part is available as an individual replacement part. It is a genuine OEM part for use with specific models of snow throwers, lawn tractors, electric mowers, chippers, and log splitters from Bolens, Cub Cadet, Craftsman, Poulan, Ryobi, Toro, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

Wing knob for lawn mowers and snow blowers. Secures chutes, bagger frames, and adjustable components. Replace if cracked, broken, or missing.

This is a dual cable fitting, designed to work with snowblowers. The cable fitting holds the auger cable in place, ensuring that it does not become a safety issue. The cable simply runs through the fitting, and the part holds it in place. Cable fittings are made from durable plastic and are not moving parts. However, they can suffer damage in several different ways. Plastic becomes brittle over time and through exposure to the elements, and the fitting may eventually crack and break. It is also possible to damage the fitting through contact with a hard surface while using the snowblower. Replacing a dual cable fitting is not difficult, although it will require a socket set. Locate the fitting on the handle of the snowblower and remove the mounting bolt(s). Remove the fitting and replace it with the new one. Be careful that the cables are properly routed inside the new fitting, then replace the mounting bolt(s). This is a genuine OEM part, and it is sold individually. This dual cable fitting is compatible with Craftsman, MTD, and Yard Machine snow blowers.

Extension spring that mounts the drive plate assembly to the housing frame on snowblowers. Replace if broken, stretched, or missing for secure mounting.

Shoulder spacer for lawn tractors and riding mowers. Installs to maintain proper spacing between components. Replace if worn, damaged, or missing.

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

Lower flexible drive shaft for line trimmer attachments. Mounts inside the lower boom housing to drive the trimmer head. Replace when worn round or cracked.

Snowblower not clearing snow properly? Worn rubber paddles reduce snow removal efficiency. This auger paddle kit restores clearing power in about 30 minutes.

This part is an idler pulley. The idler pulley applies tension to and guides the engine drive belt. A wrench set is needed to perform any repair involving the idler pulley part.The idler pulley can become worn over time with normal use. Wear to the pulley can cause the belt to slip. Signs that the idler pulley needs to be replaced include squealing noises coming from the equipment, the engine stalling, or overheating. The idler pulley is an essential component and it is important to replace this part if it becomes worn, broken, or damaged in any way.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. This idler pulley is compatible with lawn tractors and snowblowers manufactured by MTD, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, and Husky.

30-inch shave plate blade for snow throwers. Installs at the auger housing base to protect surfaces. Replace when worn, cracked, or damaged.