Poulan Parts

Engine won't start or pull cord stuck? This recoil starter assembly restores pull-start function on hedge trimmers. Moderate DIY repair in 30-45 minutes.

Replacement cutting blade for hedge trimmers. Metal teeth contact cutting surface and can break, chip, or wear over time. Installs on trimmer head.

Piston ring seals the gap between piston and cylinder wall in small engine equipment. Replace if worn, cracked, or causing compression loss.

Pleated air filter captures debris before it reaches the carburetor and engine. Replace when dirty or clogged to maintain performance. Verify fit using your model number.

This is a genuine ignition module for Husqvarna engines on select outdoor lawn equipment. The ignition module includes the ignition coil and spark plug connector in a single piece. This module is used to transfer the electric charges from the flywheel magnets. This ignites the fuel-air mixture in the cylinder and creates the combustion that powers the engine. Over time, the ignition module can become worn or the spark plug connector can snap off or get damaged, causing a need for replacement. Without a properly functioning ignition module, the engine will not be able to start. This OEM ignition module is manufactured to exact standards for use in Poulan and Husqvarna string trimmers. It is a replacement for the original part and is sold as an individual unit. The spark plug and other parts and hardware will require an additional purchase. To replace this part, allow the engine to cool and disconnect the old ignition module from the spark plug. Then, detach the other side of the module and replace it with the new part. Reconnect the spark plug and the job is done. Be sure to allow the engine to cool and wear gloves when performing this repair.

Replacement flywheel assembly for gas chainsaws. Mounts to the crankshaft with magnets that generate ignition charge. Replace if cracked or damaged.

Control cable wire harness assembly for grass line trimmers. Replaces damaged, frayed, or broken wiring harnesses. Essential for restoring connections.

Fix fuel leaks or engine flooding on your riding mower with this fuel check valve. Controls fuel flow between tank and carburetor. Easy DIY repair.

Replacement bar adjustment kit for chainsaws. Includes adjustment bolt, retainer ring, and pin. Installs inside clutch cover to maintain proper chain tension. Replace if broken, worn, or missing.

Fix chain oil leaks and inadequate bar lubrication with this chainsaw oil pump kit. Ensures proper oil flow to bar and chain during operation.

This replacement carburetor kit is a genuine OEM parts kit for Craftsman hedge trimmers. The carburetor takes gasoline from the fuel line and mixes it with air from the intake valve to make a balanced fuel that is ready for combustion. Depending on how much fuel or air pass into the carburetor, the engine may run faster or slower. The most common reason for a carburetor to break down is if it is clogged with engine gunk. While it is sometimes possible to clean out a carburetor, if left for too long, the damage can be irreparable and the part will need replacing. First, remove the air filter and filter housing using a socket wrench. This will give access to the damaged carburetor and make it easier to unhook from the links that hold it in place. Be sure to set the gaskets firmly in place and then reassemble with the new part. This replacement carburetor is designed for use only with Craftsman appliances. It comes sourced directly from the original manufacturer and includes a carburetor and two gaskets.

This genuine replacement ignition module is part of the starting system in select models of gas string trimmer/edger units. It connects the spark plug to the engine and supplies the electric current to generate the spark for ignition. In the event that the module wears out or becomes defective, the engine may fail to start. With a faulty ignition module, it will be difficult to operate equipment if it works at all, which is why an immediate replacement with an OEM part like this is necessary. This genuine OEM ignition module is manufactured by Husqvarna and compatible with select trimmers from Poulan, Weed Eater, and Husqvarna. This unit includes the ignition module, the rubberized wire, and the spark plug boot or cap. Hardware and other components are not included. It may be a good idea to replace the spark plug when replacing the ignition module if it has not been replaced recently. Be sure to wear gloves and allow the engine to cool before doing any repairs on the ignition or other engine components. Be sure to disconnect the power supply before beginning any repairs for safety, as well.

Replacement fuel cap assembly for gas leaf blowers and trimmers. Seals the fuel tank to prevent leaks and evaporation. Order when cap is cracked or missing.

Replacement fuel tank cap assembly for gas blowers and trimmers. Includes retainer connection. Replace if your cap is cracked, won't seal properly, or missing.

Adjusts chain bar tension on chainsaws. Replace if knob is cracked, stripped, broken, or missing to maintain proper chain tightness and control.

Fix a chainsaw chain that won't stop spinning or won't turn at all. This clutch assembly restores safe operation when the clutch seizes open or closed.