Range / Cooktop / Oven Burner & Related Parts

This gas pressure regulator controls and stabilizes incoming fuel supply to the appliance's burner system, helping ensure consistent flames and reliable operation. Replace it if pressure is unstable or burners/oven won't heat or ignite correctly. What it does:

• Reduces household gas supply to the appliance-rated pressure for proper burner performance
• Maintains steady pressure as burner demand changes to prevent over/under-firing
• Helps prevent yellow, lifting, or flickering flames and sooting caused by pressure issues

• 1 gas pressure regulator

• Shut off gas supply and disconnect power before servicing
• Observe flow-direction arrow on the regulator body; install between supply and appliance manifold
• Use approved gas-rated thread sealant on threaded connections; do not overtighten
• After installation, check all joints for leaks with a non-corrosive leak-detection solution; correct any leaks before use

The Cap-Burner Kit is an OEM part for Whirlpool ranges. It includes the required  4 burner caps. (2 large, 1 medium, 1 small) to replace a faulty gas burner on the cooktop.

Causes may be normal wear over years of heating cycles, chemical corrosion from repeated cleaning, or impact damage to delicate burner parts.

Symptoms of a bad burner cap or head can include:

• Uneven or unstable flame patterns
• Burners that intermittently light or go out
• Reduced heat output from affected burners
• Rust or cracking visible on burner caps

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This gas pressure regulator controls and stabilizes the incoming gas to your appliance, maintaining correct manifold pressure for consistent burner flames and reliable oven performance. Replacing a weak regulator can restore even heating across the unit. What it does:

• Reduces incoming supply pressure and maintains proper manifold pressure to the appliance
• Helps ensure uniform flame height and stable temperatures
• Symptoms may include weak or fluctuating flames on multiple burners, delayed ignition, or oven not reaching set temperature
• Set up for the correct gas type (natural/LP) during installation per your model's conversion procedure

• Includes: 1 gas pressure regulator

• Disconnect power and shut off gas; allow the appliance to cool before service
• Observe gas-flow direction and regulator orientation; transfer any model-specific fittings from the original part if required
• Use gas-rated thread sealant on threaded connections and leak-test all joints with an approved method after installation
• Verify proper natural gas/LP configuration per your model instructions

Restore steady, even flames with this surface burner cap. It sits atop the burner head to shape the flame and shield the burner from spills and debris, helping keep lighting quick and cooking performance consistent.

• Shapes and centers the flame for efficient, even heating
• Protects the burner head from spills and food debris
• Helps proper ignition by maintaining the correct gap and alignment
• Typical symptoms: uneven or yellow flames, delayed ignition or constant clicking, visible chips/warping, or a missing cap

• Turn all controls off and allow the cooktop to cool completely
• Lift off the old cap; clean the burner head and igniter area
• Center the new cap on the burner head so it sits level and fully seated
• If ignition is delayed or the flame is uneven, re-seat and realign the cap

The Surface Burner and Electrode is an OEM part for Whirlpool cooktops and ranges. This component is essential for igniting the gas burner, ensuring efficient and reliable cooking performance. The burner provides a stable flame for cooking, while the electrode generates the spark needed to ignite the gas. Includes the igniter. The compatible screw is part number WP3368921 / AP6008125

You should replace the surface burner and electrode if they become faulty. Causes of a bad surface burner and electrode can include regular wear and tear, food residue buildup, or damage from high heat. A malfunctioning burner or electrode can lead to ignition issues and inefficient cooking.

Symptoms of a bad surface burner and electrode include:

• The burner not igniting or taking multiple attempts to light
• Weak or inconsistent flames
• Clicking sound without ignition when trying to light the burner
• Uneven cooking or hotspots on cookware

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This surface burner channels gas through its ports to create an even, controllable flame on your cooktop. Replacing a worn or clogged burner restores reliable ignition, proper flame shape, and consistent heating performance.

• Directs gas from the orifice through burner ports to produce the cooking flame
• Interfaces with the spark electrode for fast, consistent ignition
• Helps maintain even heat across the pan
• Common symptoms: burner won't light, weak or uneven flame, yellow tips, delayed ignition or popping

• Disconnect power and shut off gas; allow the cooktop to cool completely
• Remove grate and burner cap; detach mounting hardware as applicable and lift off the old burner
• Align the new burner with the orifice and igniter; reinstall hardware and cap
• Restore gas and power, then check for leaks and verify proper ignition and flame quality

This auxiliary surface burner head mounts over the orifice on your gas cooktop/range and distributes gas through precision ports for an even flame. Replacing a clogged or damaged head restores fast ignition and consistent heat on the small burner. What it does:

• Distributes gas through ports to produce a stable, even flame on the auxiliary burner
• Interfaces with the igniter electrode for quick, reliable lighting
• Common symptoms of a worn/clogged head: burner won't ignite or clicks without lighting; weak, uneven, or yellow flame; delayed ignition
• Helps restore proper simmer performance after corrosion, warping, or blocked ports

• 1 auxiliary burner head

• Shut off gas and disconnect power; allow the cooktop/range to cool completely
• Remove grate and burner cap, then lift off the old head; clear debris from the orifice and around the igniter (do not enlarge burner ports)
• Position the new head over the orifice and igniter; align locating features and seat fully; if your model uses screws, tighten them evenly without over-torquing
• Reinstall the cap and grate, restore gas/power, and verify even flame and normal ignition

The Surface Burner Base is an OEM part for Whirlpool ranges and cooktops. This component is a critical part of the stove's burner assembly, housing the gas outlet and providing a stable platform for the burner cap and flame spreader. It is specifically designed to handle the rigors of daily cooking, ensuring an even and controlled flame that enhances your cooking precision.

Symptoms of a failing Surface Burner Base include:

• Uneven flames or poor heat distribution
• Difficulty in lighting the burner
• Gas leaks detected around the burner area
• Visible signs of corrosion or damage to the base

Common causes for burner base issues can include continual exposure to high temperatures, spills that lead to clogging or corrosion, and normal wear and tear. 

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This front inner panel is the structural sheet that forms the inside of the appliance's front assembly. Replacing a damaged panel restores proper fit, alignment, and appearance so the front opens, closes, and seals as designed. What it does:

• Forms the inner structural surface of the front assembly
• Provides mounting points for attached hardware and trim
• Helps maintain correct alignment for smooth opening/closing
• Replaces panels that are bent, rusted, or cracked, which can cause rattles, gaps, or poor fit

• One front inner panel

• Disconnect power; shut off water or gas before servicing
• Support the door/drawer/front while removing fasteners to prevent strain or damage
• Handle sharp metal edges; wear cut-resistant gloves and eye protection
• Transfer original screws, clips, insulation, seals, and trim; check alignment before fully tightening

This flame spreader sits between the burner base and cap to distribute gas evenly through the burner ports. Replacing a clogged or warped spreader restores reliable ignition and a steady, balanced flame for consistent cooking. What it does:

• Distributes gas to create an even, circular flame pattern
• Supports reliable ignition by positioning ports around the electrode
• Helps maintain proper heat output and flame stability
• Symptoms include uneven/weak flames, yellow flames, delayed ignition, or a burner that won't light

• One flame spreader

• Disconnect power and shut off gas; allow the cooktop to cool completely
• Remove grate and burner cap; lift off the old spreader (remove retaining screw if present)
• Align the new spreader over the orifice and igniter; seat fully and secure
• Do not clear ports with hard objects; use a soft brush and verify proper flame and ignition after reassembly

This burner cap sits on top of the gas burner head to shape the flame and shield it from spills. Replacing a damaged or missing cap restores proper flame pattern, reliable ignition, and even heating.

• Shapes and disperses the burner flame for even cooking and proper simmering
• Shields the burner head/orifices from spills, grease, and debris
• Must sit level and centered for consistent ignition and flame quality
• Replace if cracked, chipped, warped, missing, or if flames are uneven or yellow

• Allow the appliance to cool completely. Turn off gas supply and power before servicing.
• Lift off the old cap; clean and dry the burner head so the new cap seats properly.
• Center the new cap on the matching burner; it should sit flat with no rocking or gaps.
• Light the burner to verify an even, blue flame; realign the cap if ignition is delayed or the flame is uneven.

Replace a clogged or damaged rear burner with this surface burner head in black. It channels gas to the flame ports so the rear burner lights reliably and delivers a consistent, even flame for everyday cooking.

• Directs gas through precisely sized ports to form the rear burner flame pattern
• Interfaces with the spark igniter/electrode for dependable ignition
• Helps restore proper burner performance when ports are worn, corroded, or blocked
• Common symptoms: burner clicks but won't light, uneven or weak flame, yellow tipping, delayed ignition

• Shut off gas supply and disconnect power before servicing
• Remove grate and burner cap; take out mounting screws and lift the old burner head straight up over the igniter
• Align the new head over the orifice and igniter; secure with the existing screws
• Reassemble and test for proper ignition and flame on all burners

This burner cap sits on a sealed gas burner to shape the flame and protect the burner head. Replace to restore even heat and reliable ignition when the original is damaged, warped, or missing.

• Shapes and distributes the flame for even heating and better simmer control
• Shields burner ports from spills and debris to help prevent clogging
• Aids proper ignition and flame stability when correctly seated
• Common symptoms: uneven or yellow flames, sputtering, delayed ignition, continuous clicking, visible chips/warping

• Allow the cooktop/range to cool; shut off gas and power as needed
• Match the cap to the correct burner position for your model
• Lift off the old cap; clean the burner head/ports; set the new cap flat and centered
• Light and test; if flame is uneven or noisy, reseat and re-test

This replacement surface burner head restores proper flame on your gas range or cooktop. It mixes gas and air and directs the flame through the ports for even heat and reliable ignition when the original head is clogged or damaged.

• Distributes gas through flame ports for stable, even heating
• Supports quick, consistent ignition when paired with a working igniter
• Helps address weak, uneven, yellow, or noisy flames
• Replaces burner heads that are warped, pitted, cracked, or corroded

• Disconnect power and shut off gas; allow the cooktop to cool completely
• Remove the burner cap, lift off the old head, and clear debris from the seating area
• Align the new head with the igniter/electrode and locating features; seat it fully and level
• Restore gas and power; verify ignition and check for a uniform flame around all ports

This surface burner valve regulates gas flow to a top burner on your gas range or cooktop. The simmer version enhances low-heat control so the flame adjusts smoothly from a steady simmer to a full boil. What it does:

• Regulates gas to the surface burner as you turn the knob, controlling flame size
• Simmer variant improves stable low-flame performance at lower settings
• Common failure symptoms: burner won't light though the igniter sparks, flame won't adjust or stays at one level
• Knob feels stiff/binds or the stem no longer aligns correctly with settings

• 1 surface burner valve

• Disconnect electrical power and shut off the gas supply before servicing
• Remove the control knob and access the valve/manifold from the control panel or cooktop top
• Note the original valve's orientation for your burner position; transfer mounting hardware as needed and tighten all gas connections securely
• After reassembly, restore gas and check every joint for leaks with an approved leak-detection solution; verify proper flame and adjustment

The burner cap is an OEM part for Whirlpool gas ranges. It is located on the cooktop burner and helps to distribute the gas evenly, allowing for a consistent and controlled flame.

A bad burner cap can occur due to regular use, wear and tear, or accidental damage. If the cap becomes worn, cracked, or clogged, it can lead to issues such as uneven heating, weak flames, or difficulty in igniting the burner.

Symptoms of a bad burner cap include:

• Uneven heating or hot spots on cookware.
• Weak or inconsistent flames.
• Difficulty in igniting the burner.
• Visible damage or debris accumulation on the cap.

If you're experiencing any of these issues, it's time to replace the Cap-Burner with this genuine Whirlpool part for proper heat distribution and reliable ignition for your gas range. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.