Range / Cooktop / Oven Heating Element

Dual

This is a replacement broil element for the oven's upper heating function. It restores high-heat broiling and top-surface browning so you can sear, brown, and finish foods as intended. What it does:

• Produces the direct, high heat required for broiling and browning
• Replaces a burned-out, visibly damaged, or non-heating upper element
• Restores even top-heat for recipes that require searing or finishing
• Helps eliminate weak or no heat from the oven's broil function

• One broil element

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and use basic hand tools to remove mounting screws and the old element
• Handle the new element carefully to avoid bending or damaging terminals

This heater assembly replaces the dryer's heating unit to restore normal drying performance and consistent drum temperatures. It's a direct-fit replacement designed to match the OEM heater layout and electrical connections. What it does:

• Reheats incoming air so the dryer can remove moisture from clothes.
• Works with the dryer's blower and thermostat to maintain operating temperature.
• Commonly used when the dryer produces little or no heat, or runs long cycles.
• Helps resolve intermittent heating caused by a failed heating element or broken heater housing.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Access requires removing the dryer cabinet or rear panel; follow OEM disassembly steps.
• Inspect related parts (thermal fuse, high-limit thermostat, wiring, connectors) for damage while replacing the heater.

This replacement grill (broil) heating element restores high, direct heat for broiling and browning in the oven. It lets you crisp and brown food quickly so broil functions work like new. What it does:

• Provides the intense direct heat required for broiling and grilling
• Replaces a burnt-out or broken upper oven element to restore broil performance
• Helps eliminate problems like food not browning or uneven broiling
• Visible breaks, blisters, or open circuits on the element are common failure signs

• Disconnect power to the appliance before starting any repair to avoid shock
• Handle element carefully to avoid bending or damaging the terminals
• Reconnect wiring securely

This broil heater assembly replaces a failed upper-oven broil element to restore top-heat cooking and browning. It fits many GE ovens and provides a direct-replacement heating element for broiling performance. What it does

• Heats the top of the oven cavity for broiling, broil-browning, and crisping finishes
• Restores proper broil function when the element is visibly burned, broken, or not heating
• Works with the oven's broil control to reach required temperatures for short, high-heat cycles
• Helps eliminate uneven browning caused by partial or intermittent element failure

• One broil heater assembly

• Disconnect power to the range/oven at the breaker before starting any repair
• Access typically requires removing the oven back panel or interior broil access screws; keep track of fasteners
• Avoid contact with the element until fully cool; wear gloves and eye protection as needed
• Verify the part number on the oven tag and compare the old element to this assembly before installation

This heating element kit replaces a failed heating element to restore normal heating in compatible laundry or cooking appliances. It provides the core heating component needed to get your appliance producing heat again. What it does:

• Replaces a damaged or burned-out heating element that stops the appliance from heating
• Helps resolve symptoms like no heat, weak or inconsistent heating, or tripped thermal cutouts
• Restores the appliance's ability to reach and maintain operating temperatures for normal cycles
• Works as the direct replacement heating component shown in OEM parts listings

• One heating element kit as shown

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock risk
• Handle the element and terminals carefully to avoid bending or damaging mounting tabs
• Confirm correct terminal connections and secure mounting per the appliance wiring diagram

This tubular bake element is the lower heating element for electric ovens, restoring oven bake heat and even cooking performance. It replaces a damaged or non-heating element to get your oven back to regular baking temperature. What it does:

• Produces the primary radiant heat from the bottom of the oven for baking and roasting
• Common symptom: oven won't reach or hold set bake temperature
• Common symptom: visible breaks, blistering, or arcing on the element surface
• Common symptom: uneven baking or loss of heat from the bottom of the cavity

• One bake (lower) element

• Disconnect power at the breaker or unplug the range before any work
• Access typically requires removing the oven floor or lower access panel and unscrewing the element terminals
• Inspect wiring and terminal connections for heat damage; replace or repair as needed

This genuine surface coil element replaces a damaged or non-working burner on an electric cooktop to restore even heating for everyday cooking. It fits standard countertop ranges and reconnects to the existing socket for simple swap-outs. What it does:

• Heats cookware by converting electrical power into a cooking surface heat source
• Replaces a cracked, broken, or non-heating burner element
• Fixes symptoms like no heat from a burner, intermittent heating, or uneven cooking
• Works with the existing element receptacle and trim/reflector assembly when compatible

• Disconnect power at the breaker before attempting any service
• Allow the cooktop to cool completely and use gloves to avoid cuts
• Remove and retain any trim or mounting hardware; install using original screws/connectors

This oven bake element is the lower heating element that provides consistent radiant heat for baking and roasting. It restores the oven's ability to reach and hold baking temperatures for even cooking results. What it does:

• Heats the oven cavity from the bottom for baking and roasting
• Replaces a broken or visibly damaged element that won't heat or glow
• Helps correct uneven baking or failure to reach set temperatures
• Works with the oven's thermostat and controls to maintain cooking heat

• One lower/bake oven element

• Disconnect power to the range or oven at the breaker before servicing
• Access may require removing the oven floor or rear access panel; handle terminals carefully
• Inspect terminal connections and mounting hardware; tighten or replace as needed

This bake element is the oven heating element that produces the lower radiant heat used for baking and roasting, restoring even oven temperatures and consistent cooking results. What it does:

• Heats the oven cavity during bake cycles to cook food evenly
• Replaces a broken or visibly damaged element that won't glow or heats weakly
• Helps correct symptoms like no heat on bake, uneven baking, or error codes tied to heating failures
• Works as the direct replacement heating element assembly in compatible ranges and wall ovens

• One bake element

• Disconnect power to the appliance before starting any repair
• Allow the oven to cool completely and wear gloves to avoid cuts from sharp edges
• Access typically requires removing the oven cavity or rear access panel and disconnecting two terminal connectors
• Verify correct fit and secure electrical connections;

This boiler is the dishwasher water-heating assembly that provides the hot wash and rinse temperatures needed for effective cleaning. Replaces a failed boiler to restore normal heating during dishwasher cycles. What it does:

• Heats water used during wash and rinse cycles so detergent can clean effectively
• Helps maintain proper cycle temperatures for sanitizing performance
• Stops working when the element fails or the boiler leaks or overheats
• Often linked to no-heat cycles, prolonged wash times, or error codes related to water temperature

• Disconnect power and water supply before starting any repairs
• Inspect for leaks and damaged connectors; replace any worn mounting hardware or seals
• Handle electrical connections carefully and follow the appliance's service manual for wiring and testing

This is a replacement hotplate surface element that restores a working cooking surface on compatible electric ranges. It provides a direct heating surface for pots and pans and helps ensure even heat transfer during cooking. What it does:

• Heats cookware when the burner control is turned on to allow stovetop cooking
• Replaces a cracked, damaged, or non-heating surface element
• Helps correct uneven heating or intermittent burner operation when element is the fault
• Works with the range's burner control and terminal block to complete the circuit

• One hotplate surface element

• Disconnect power to the appliance before starting any repair to avoid shock hazard
• Access the element from the cooktop or underside per your model's service instructions
• Remove and retain any mounting hardware; reconnect terminals in the same orientation
• Inspect burner terminals and wiring for damage; replace damaged wiring or connectors before testing

This bake element heats the oven cavity so food cooks evenly on bake settings. It replaces a failed or damaged element to restore proper baking performance and clear heating issues. What it does:

• Heats the bottom of the oven for bake cycles
• Replaces elements that are broken, visibly burnt, or not producing heat
• Helps resolve uneven cooking, no-heat on bake, or error codes related to open elements
• Works with matched oven control settings to maintain set temperatures

• One bake/heating element

• Disconnect power to the appliance before starting any repair
• Handle the element carefully to avoid bending or damaging terminals
• Verify electrical connections are tight and secure; replace mounting screws if worn

This broil unit is the upper-oven heating assembly that provides direct high heat for broiling, browning and finishing dishes. Replaces a worn or failed broil element to restore proper broil performance. What it does:

• Produces the direct radiant heat used for broiling and browning food
• Replaces a visibly burnt, broken, or non-heating broil element
• Helps correct uneven browning or lack of upper-oven heat during broil cycles
• Works as the main heat source for the oven's broil function

• One broil unit assembly

• Disconnect power to the appliance at the breaker or unplug before servicing
• Allow the oven to cool completely; use gloves to protect hands from sharp edges
• Remove oven racks and access panel as required to reach the broil element
• Verify proper operation after installation

• Genuine OEM Part: Produced by Whirlpool for unmatched compatibility and reliability with Maytag and Magic Chef appliances.
• Spade Style Connections: Features secure spade terminals for easy electrical connections.
• Exact Fit: Sized at 16x16 inches with 2-inch deep terminals for a perfect fit in specific models.

Common Symptoms for Maytag Magic Chef Oven Bake Element WP7406P012-60:

• Oven not heating evenly or not heating at all
• Visible damage or breakage in the element
• Oven taking longer than usual to preheat
• Inconsistent baking results

Basic Troubleshooting for Maytag Magic Chef Oven Bake Element WP7406P012-60:

• Check for Visual Damage: Inspect the bake element for any signs of wear or damage. Look for blisters, breaks, or areas that might be discolored (typically a burnt orange or darker spots).
• Test for Continuity: Using a multimeter, test the element for continuity. A lack of continuity indicates that the element is faulty and needs replacement.

Installation Instructions for Maytag Magic Chef Oven Bake Element WP7406P012-60:

1. Ensure Safety: Disconnect power to the oven by unplugging it or turning off the circuit breaker.
2. Access and Remove the Old Element: Remove the oven racks for better access, unscrew the mounts, and gently pull the element forward to reach the terminals.
3. Disconnect and Replace: Detach the spade connectors from the old element and connect them to the new one. Secure the new element in place with the original screws.
4. Operational Test: After installation, reconnect power and briefly turn on the oven to ensure the new element functions correctly.