Range / Cooktop / Oven Hinge Parts

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays properly aligned, helping the door seal engage correctly for safe, reliable operation.

• Supports the weight of the door and controls opening/closing motion
• Helps maintain door alignment so latches/seals engage properly
• Wear or damage can cause sagging, rubbing, squeaking, or difficulty closing
• A misaligned door may prevent the unit from starting or sealing correctly

• Disconnect power and allow the appliance to cool before servicing
• Use gloves and eye protection; doors can be heavy and spring-loaded
• Support the door during removal to prevent damage
• Transfer any hardware from the old hinge to the new one if re-usable

This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.

• Provides the pivot and spring action at the door's upper mounting point
• Maintains door alignment for proper gasket contact and heat seal
• Typical symptoms of a failing hinge: door won't close fully, sags, binds/rubs, or pops open
• A poor seal from a worn hinge can lead to heat loss and uneven baking

• Disconnect power and allow the oven to cool completely before service
• Support the door; many models require removing the door to access the hinge
• Install at the factory mounting points and ensure the hinge fully engages the receiver
• After replacement, check door alignment and that the seal contacts evenly

This oven door hinge assembly controls the door's movement and keeps it sealed against the frame. Replacing a worn hinge restores smooth opening and a tight close, helping maintain temperature and consistent cooking performance.

• Provides spring-assisted pivot to support the oven door during opening and closing
• Maintains alignment and helps the door stay fully closed against the gasket
• Direct replacement for bent, weak, or broken hinges
• Common symptoms: door won't close fully, drops or slams open, sits uneven, squeaks, or allows heat to escape

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door; engage hinge locks or insert hinge pins and support the door while lifting it off
• Springs are under tension—use caution and wear gloves/eye protection
• After replacement, check door alignment and gasket seal; many replace both hinges together for even operation

This oven door hinge is used on the black and designer white models. Two are used per oven.

This oven door hinge supports and guides the door so it opens and closes smoothly and seals properly. Replacing a worn hinge can restore correct door alignment and help prevent heat loss from a door that won't close tightly.

• Supports the oven door and controls its opening/closing movement
• Helps maintain proper door alignment and seal for stable temperatures
• Replace if the door won't stay closed, sags, binds, or slams
• Symptoms can include heat escaping around the door, uneven baking, or creaking/grinding when moving the door

• Disconnect power at the breaker; allow the oven to cool completely
• Remove the door; use hinge locks/pins if the design provides them
• Install the hinge in the original orientation and mounting points; re-seat the door and verify latch engagement
• Check door alignment; replacing both hinges together can help ensure even closing force

Kit includes 4 pins.

The door hinge is an OEM part for Whirlpool ranges. This piece serves as the anchor for stable, smooth opening and closing of the oven door. 

Causes of a bad door hinge include warping from repeated heat exposures and compromising its secure gateway function over time. Breakdowns disrupt workflows. 

Symptoms involve: 

• A sagging oven portal is unable to support itself when ajar  
• Grating or binding movements straining the hinge mechanism
• Difficulty latching or sealing the door during baking

This OEM Whirlpool part is also compatible with some Maytag, Jenn-Air, and KitchenAid ranges.

Right side hinge receiver for door hinge. For left side hinge receiver use WP4455605.

Restore smooth, secure door movement with this oven door hinge. A worn hinge can cause the door to sag or leak heat; replacing it helps the door close flush for better heat retention and consistent baking performance. What it does:

• Provides spring-tensioned pivot for the oven door
• Helps keep the door aligned and fully closed against the gasket
• Common fixes: door won't close fully, drops quickly, won't stay ajar, squeaks or binds
• Reduces heat loss and temperature fluctuation caused by a misaligned door

• One door hinge assembly

• Disconnect power at the breaker and let the oven cool completely
• Support the door; engage hinge locks or remove fasteners, then lift the door off per your model's instructions
• Remove the faulty hinge and install the new hinge in the same orientation; reuse mounting hardware
• Open and close the door to verify smooth motion and a tight seal before use

This Door Hinge supports and pivots the appliance door for smooth operation and a square, reliable close. Replacing a worn hinge restores alignment so the door seals properly and opens and closes without binding or noise. What it does

• Supports door weight and provides the pivot point for opening and closing
• Maintains proper door alignment to help ensure an even gasket seal
• Restores smooth, consistent door movement
• Common symptoms: door droops or rubs, squeaks/grinds, or won't close flush

• Includes 1 door hinge

• Disconnect power before servicing
• Support the door and use a helper; remove contents as needed to reduce weight
• Mark hinge position and transfer any spacers/bushings in the same order
• Tighten mounting fasteners, then check alignment and gasket contact; adjust as needed

Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.

This is a replacement oven door hinge that supports and controls the swing of the oven door for smooth opening and secure closing. Restoring the hinge helps the door seal properly, improving heat retention and overall cooking performance.

• Supports the oven door's weight and movement
• Helps the door close fully to engage the gasket
• Worn hinges can cause sagging, misalignment, or a door that won't stay closed
• Also lead to heat loss and longer preheat times

• Disconnect power and allow the oven to cool completely before service
• Remove the door per your model's manual; support the door to prevent strain on the glass
• Transfer any locking clips/brackets as required by the model
• Test door operation and seal engagement after installation

This hinge receptacle mounts in the oven cabinet and provides a secure receiver for the door hinge arm. Replacing a worn receptacle restores smooth hinge engagement and helps the door close and seal correctly.

• Receives and secures the oven door hinge in the appliance frame
• Maintains proper door alignment for consistent closing and sealing
• Common symptoms: door won't close fully or stay closed; door sags or feels loose; difficulty reinstalling the door; visible wear or deformation at the receiver
• Also referred to as a hinge receiver/bracket in some catalogs

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door; hinge springs are under tension—use caution
• Remove the old receptacle from the cabinet and install the new one using existing fasteners, aligning the slot with the hinge arm
• Reinstall the door and verify smooth engagement and full closure

Restore smooth, controlled door movement and a tight oven seal with this door hinge. Replacing a worn hinge helps the door close fully, prevents heat loss, and brings back the original opening tension on top or bottom compartments.

• Controls door swing and spring tension for smooth opening/closing
• Maintains alignment so the door gasket seals evenly
• Helps the door stay closed during cooking and hold at designed positions
• Common symptoms: door won't close fully, drops/sags, uneven gap, squeaks/binds, or heat escaping

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the door; support it to safely relieve hinge spring tension
• Note hinge orientation and attachment points; transfer and secure the hinge using existing mounting locations
• After reassembly, verify latch engagement and even gasket contact; many ovens use two hinges—replace in pairs if both show wear

This right-hand oven door hinge assembly supports and counterbalances the door so it opens smoothly and closes firmly against the gasket. Replacing a worn hinge restores proper alignment and heat retention for consistent cooking performance.

• Provides the pivot point and spring tension for the oven door
• Helps the door open smoothly and close completely for a tight seal
• Wear or damage can cause sagging, misalignment, or slamming/falling open
• Heat loss from a poor seal may lead to long preheat or temperature fluctuations

• Disconnect power and allow the oven to cool completely before servicing
• The hinge is spring-loaded—support the door and use care to avoid injury
• Remove the door per your model's instructions, then replace the right-side hinge
• After installation, adjust per service guidance if needed

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.