Range / Cooktop / Oven Hinge Parts

The Oven Door Hinge is an OEM part for Whirlpool ranges. It is essential for the smooth operation and stability of the oven door, allowing it to open and close properly. This hinge supports the weight of the door and ensures it stays securely in place during use.

Causes of a bad oven door hinge can include wear and tear from frequent use, rust or corrosion, and damage from accidental force or misalignment. 

Symptoms of a bad oven door hinge include:

• The oven door not closing completely or evenly
• Difficulty in opening or closing the door
• The door feels loose or makes unusual noises when moved

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Right hinge for Colored/Clear Doors.

This left-side oven door hinge supports the door and controls its spring-loaded movement so it opens smoothly and closes firmly, helping maintain a tight seal and consistent cooking performance.

• Provides spring tension and a pivot point for controlled opening and closing
• Aligns and pulls the door fully closed against the gasket
• Restores smooth, even door movement
• Common symptoms of a worn hinge: door won't close fully or sags; slams/falls open; feels loose or stiff; heat escaping or oven light staying on

• Disconnect power and let the oven cool completely before servicing
• Support the door; engage hinge locks or remove the door at the stop position per your model
• Springs are under tension—use gloves and caution
• After installation, verify alignment and that the door closes and seals properly

Left hinge for Colored/Clear Doors.

This hinge supports and controls the movement of your oven door so it opens smoothly and closes tightly. Replacing a worn hinge restores proper door alignment and sealing to help the oven heat efficiently and safely. What it does:

• Supports the oven door and regulates opening/closing tension and angle
• Helps keep the door fully closed to maintain temperature and engage any door switch
• Replace if the door sags, won't stay closed, opens too quickly, or binds/squeaks
• A weak or bent hinge can cause heat loss and longer preheat times

• 1 door hinge

• Disconnect power; for gas ranges, also shut off the gas supply
• Remove the door per your model's instructions; secure hinge arms with locks or pins if applicable
• Unfasten and replace the hinge using the existing mounting points and hardware
• Adjust per your service instructions if needed

This oven door hinge will work for either the left or right side of an oven door. The hinges on the door are responsible for ensuring that the door can open and close properly. If one or both of the hinges are not working correctly, the door may become difficult to open and close or may not stay on the oven. If this happens, the hinges should be replaced before using the oven.Made of durable metal, the oven door hinges should last a long time. However, they can become damaged and may need to be replaced. If there is too much pressure placed on the door or hinges, it could cause them to break. Owners may want to replace both of the hinges at the same time. Be sure that the oven is off and cooled before replacing this part.The oven door hinges are for use with certain ovens from KitchenAid, Whirlpool, Inglis, and Kenmore. The hinges are genuine OEM replacement parts sourced from the manufacturer. Each hinge is sold individually. Owners that need to replace both hinges should buy two.

This door hinge kit replaces worn or broken hinge components so the door opens and closes smoothly and aligns with the latch. It restores proper door support and helps prevent sagging, binding, and misalignment. What it does:

• Maintains correct door alignment at the hinge pivot points
• Helps fix a door that sags, rubs, squeaks, or won't close/latch properly
• Can resolve intermittent operation caused by misaligned latch/interlock engagement
• Direct replacement designed to match the original fit and function

• One hinge kit

• Disconnect power at the breaker or unplug the appliance before servicing
• Support the door during removal and installation to prevent damage or injury
• Note hinge orientation and transfer any reusable hardware from the original
• After installation, verify the door closes evenly and the latch/interlock engages

The Door Hinge is an OEM replacement part for GE ranges. It allows for smooth and controlled opening and closing of the oven door. It features a sturdy metal construction and is designed to withstand the repeated use and high temperatures of the oven.

Symptoms of a faulty door hinge include:

• Oven door not closing or sealing properly
• Difficulty in opening or closing the oven door
• Uneven or loose door seal

A bad door hinge can occur due to wear and tear over time, excessive weight or force applied to the door, or damage from accidental impact. If you notice issues such as the oven door not closing properly, difficulty in opening or closing the door, or an uneven seal, it may be time to replace the old or damaged door hinge with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This hinge is for painted door only. For stainless steel door use WP8272822.

The Oven Door Hinge is an OEM part for Whirlpool ovens. This hinge is essential for the proper operation of the oven door, ensuring it opens and closes smoothly and stays securely in place when shut. This hinge measures 14-1/2" in height. 

Common causes include repeated use, which can lead to wear and tear, accidental damage, or exposure to high temperatures over time. 

Symptoms of a bad oven door hinge include:

• The oven door not closing properly
• A loose or sagging oven door
• Difficulty in opening or closing the oven door
• The door not staying in the desired position

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven door hinge supports the door and controls its movement. Replacing a worn hinge restores smooth opening and closing and helps the door seal properly against the gasket for accurate temperatures and safer operation.

• Supports and pivots the oven door during opening and closing
• Provides closing force to help the door seal against the gasket
• Helps maintain correct door alignment
• Common symptoms of a worn hinge: door won't close fully or sits uneven, drops/slams or won't stay partially open, heat loss or long preheat, squeaking

• Disconnect electrical power; for gas ranges, also shut off the gas supply. Allow the oven to cool completely
• Support the door; hinges are spring-loaded—use caution when releasing/engaging hinge locks if equipped
• Transfer any original mounting screws/brackets as needed
• For best results, replace both door hinges together to maintain even alignment

This oven door hinge is a replacement for many models of ovens. Oven doors will have two hinges. If there is a problem with one or both of the hinges, it means that the door will not open and close properly. It might not stay closed, or it could be difficult to open. This would make it impossible to use the oven, and the hinge should be replaced as soon as possible.An oven door hinge could become damaged for a host of reasons. When the door is open, too much pressure could be placed on the hinge, which could cause it to break. It could become corroded over time, or the spring might wear down. When there are issues, the owner will want to replace the hinge to ensure the door stays closed. Owners should always make sure the oven is off and not powered before beginning work.The oven door hinge will work with certain models of ovens from Whirlpool, Maytag, Amana, Jenn-Air, Norge, Crosley, and Magic Chef. This is a genuine OEM replacement part, and it is sold individually. If both of the hinges need to be replaced, the owner will need to buy two.

This replacement oven door hinge is engineered for stainless-steel door assemblies. It restores smooth opening and a tight seal, helping the oven heat efficiently while keeping the door closed and the light off. What it does:

• Supports the door's weight and controls opening/closing tension
• Draws the door fully closed to compress the gasket and retain heat
• Helps prevent door sagging, slamming, or uneven alignment
• Common failure symptoms: door won't close fully, heat escaping, poor temperature regulation, door won't stay shut, or oven light stays on

• One oven door hinge assembly

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door per your model's instructions; engage hinge locks or insert removal pins if provided
• Support the door and hinge arms—springs are under tension; transfer any reusable hardware
• After installation, verify the door closes evenly and seals against the gasket

The Wall Oven Hinge is an OEM part for Frigidaire wall ovens. This hinge is responsible for securely yet smoothly opening and closing the oven door. It is an essential component that allows for easy access to the cooking chamber.

Causes of a bad hinge can include wear and tear over time, exposure to heat, or damage due to excessive force.

Symptoms of a bad hinge include:

• The door not sitting flush or securely when closed
• Difficulty in opening or closing the door
• The door sagging or becoming loose on its hinges
• Noisy or grinding sounds coming from the hinge area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door hinge restores smooth, controlled opening and a tight seal on the oven door. It supports the door's weight with spring tension so the door closes fully and stays positioned without slamming or sagging.

• Provides the spring-loaded pivot that controls oven door movement
• Helps ensure the door closes flush for a proper seal and heat retention
• Common symptoms: door won't close fully, drops or slams, won't stay at a set angle
• Reduces squeaks/binding and corrects uneven gaps around the door

• Disconnect power to the range or wall oven; shut off gas supply if applicable
• Remove and support the door to access hinges
• Springs are under high tension—use caution and proper locking method; wear gloves and eye protection
• After installation, verify door alignment and gasket contact all around

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes flush. Replacing a worn hinge restores alignment and reliable latching to help prevent sagging, rubbing, or an uneven door gap.

• Provides the pivot point and support for the door
• Maintains proper alignment so the door closes and latches correctly
• Helps prevent door sagging, rubbing, or uneven gaps
• Common symptoms include a loose or misaligned door, difficulty closing, or squeaking/grinding at the hinge
• Replace if the hinge is bent, cracked, or binding

• Disconnect power at the breaker before servicing; wear cut-resistant gloves
• Support the door during removal and installation to avoid strain on the hinge
• Note hinge orientation and transfer original fasteners as needed
• After installation, verify the door closes evenly and latches without rubbing