Range Motor

This is the cooling fan motor that draws air across the oven cavity and control panel area to prevent overheating of surrounding cabinetry and electronic components. It typically runs during and after oven use to dissipate heat. Replace this motor if the oven shuts off unexpectedly due to overheating, the cooling fan does not spin, or you notice excessive heat around the control panel or cabinet surfaces near the range.

Fix a microwave that won't run with this motor AC drive replacement. Controls fan and turntable operation. Direct fit for multiple models. DIY repair.

Fixes loud grinding or coffee grinder noise from microwave. Simple DIY repair with 2 screws and wire connectors. Located on top, typically takes under 30 minutes.

This is a small synchronous motor used in microwave ovens to drive components such as the turntable or air damper. It operates at a steady rotational speed to ensure consistent movement during cooking. Replace this motor if the turntable stops spinning, rotates intermittently, or if you hear a humming noise without any movement.

Convection fan motor that circulates hot air inside the oven cavity for even cooking temperatures. Replace if fan stops spinning or makes excessive noise during convection baking.

This is an AC synchronous motor and switch assembly that controls the oven door lock mechanism during the self-clean cycle. It engages to lock the door before high-temperature cleaning begins and unlocks it once the cycle is complete and the oven has cooled. Replace this assembly if the oven door fails to lock or unlock, or if the self-clean cycle will not start or complete properly.

Fixes poor ventilation and smoke removal issues in downdraft ranges. This blower motor removes heat, smoke, and odors from your kitchen by drawing air.

This is the blower motor used in the downdraft ventilation system of a range. It powers the fan that draws smoke, steam, and cooking odors down and away from the cooktop surface. Replace this motor if the downdraft vent makes unusual noises, vibrates excessively, runs intermittently, or fails to turn on at all.

Fix a range cooling fan that won't shut off or makes howling noises with this motor. Requires removing oven from cabinet and back panel access.

Convection fan not working or oven heating unevenly? This motor drives the rear fan to circulate hot air. Moderate difficulty, requires rear access.

Fix a microwave turntable that won't rotate with this motor replacement. Solves spinning issues when motor receives power but fails to turn the tray.

The Blower Tangential 45mm is an OEM part for GE gas ranges. It is the convection fan that circulates heated air within the oven cavity during convection cooking cycles.

Symptoms of a bad blower tangential include:

• Lack of airflow inside the oven
• Uneven baking and roasting results  
• Inability to select convection cooking modes

Causes of failure can be worn bearings, burned out motor, or damage from excess heat over long-term use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

A replacement fan (blower) that restores airflow in compatible Bosch appliances to support proper cooling and ventilation. Installs in the appliance's air path to help maintain temperature balance and reduce strain on other components. What it does:

• Circulates air through the appliance to support cooling and ventilation.
• Helps cool motors, heating elements, or evaporator areas depending on the model.
• Common symptom relief: reduces overheating, improves cooling performance, and can stop abnormal fan noise when the original fan fails.
• Prevents related faults caused by insufficient airflow when installed correctly.

• Always disconnect power to the appliance before starting any repair.
• Handle the fan blades and motor carefully to avoid damage; avoid forcing connectors or mounting points.
• After installation, test the appliance functions and listen for normal fan operation; if unusual noise persists, re-check mounting and clearance.

Tangential blower that moves air through the oven's ventilation and control areas to help keep components cool and vent heat. Replacing a failed blower restores airflow for quieter operation and more consistent cooling around electronics. What it does:

• Circulates air across the oven vent and control area to dissipate heat; symptoms of failure include little or no airflow.
• Helps cool control electronics and nearby components; failure can cause high temperatures or thermal-related shutdowns.
• Reduces noisy or rough fan operation when bearings or motor wear.
• Supports proper venting after use to help the appliance cool down safely.

• Disconnect power to the appliance before accessing or replacing the blower.
• Allow the appliance to cool fully; remove access panels to reach the blower.
• Handle the blower and connector gently to avoid damaging the motor shaft or wiring; ensure correct orientation when reinstalling.

This blower assembly circulates air through the appliance to support drying and venting, restoring proper airflow for consistent performance. It replaces a worn or damaged fan wheel and housing to reduce overheating and poor drying. What it does:

• Moves air through the appliance to aid drying and ventilation
• Restores airflow lost from cracked, warped, or broken blower wheel
• Helps eliminate overheating, long-dry times, or reduced airflow
• Works with the motor and ducting to maintain proper exhaust flow

• One blower assembly

• Disconnect power before servicing to avoid shock or injury
• Inspect motor shaft and mounting before installing; replace any damaged hardware
• Ensure blower is oriented and secured per manufacturer alignment to prevent noise or imbalance
• Verify clear, unrestricted ducting after installation for proper performance

This small drive motor rotates the turntable plate inside the microwave to ensure even heating of food. It connects to the turntable coupler beneath the glass tray and spins at a slow, steady speed. Replace this motor if the turntable stops rotating, turns intermittently, or makes grinding noises during operation.