Need Help?
Call
Oven won't broil or heats unevenly? The broil element provides high heat from above for browning. DIY-friendly repair, usually takes 10 minutes to replace.
Removed the bake element and broil element. Tested them with a multi meter. They failed. Ordered new elements. Received them in 2 days. Installed new elements. Oven works great. Entire fix took 10 minutes to remove and test elements, 10 minutes to install the new elements. It was my first time working on an appliance, the instruction videos were great! Read more
Oven not heating properly or showing F3 error? The temperature sensor likely failed. Simple DIY fix—unplug, remove 2 screws, replace sensor.
Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more
This is a monitor or interlock switch that detects whether the microwave door is properly closed before allowing the unit to operate. It is a safety device that shuts off microwave power if the door is open or if other door switches malfunction. Replace this switch if the microwave does not start, runs with the door open, or blows a fuse when the door is closed.
The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more
Replace your refrigerator's LED light module when lights flicker, dim, or fail. Restores full interior illumination. Verify fit by model number.
Ordered the part, which was easy and smooth. Watched you tube video on how to repair. Took me 15 minutes. Easy as it could be. Read more
Oven won't heat, overheating, or controls unresponsive? This range control board manages temperature and cooking functions. Moderate DIY repair.
Replaced the oven controller. This needed the only removal of six hex screws securing the back guard rear shield, two-wire plugs on the control unit, and four Phillips screws. All are easily accessible. The only difficulty came from an apparent model design change that separated the control unit and the overlay - the labels for the control buttons (items 20 and 20a in the backyard parts diagram). Mine is a single unit (the overlay could not be removed without damage) led to the assumption that... Read more
Broil element burnt out or not heating? This top heating element provides intense direct heat for broiling. Takes 15-20 minutes to replace yourself.
Ordered a new part. Watched a YouTube video. Fixed it in 15 minutes. Knowing you need to stop the connectors from slipping into the back of the oven was the key. I used paperclips to stop the wires falling through the hole. Easy as ... Read more
Converts your gas range from natural gas to LP (propane) fuel. Includes orifices and components for burners and oven. Replace when switching fuel types.
Finding the proper conversion kit was a snap. I just plugged in the model number and Appliance Parts Pros sent the proper conversion kit. Read more
Replacement 6-inch burner bowl for electric ranges and cooktops. Houses the burner element. Replace if cracked, chipped, rusted, or discolored beyond cleaning.
Burners were an exact match for the originals and the pans fit perfectly. Vastly improved the appearance of an old cook top and allowed us to to not have to replace it before our home goes up for sale. Read more
Burner won't turn off or runs too hot? This rotary switch controls heating elements and temperature settings. Straightforward DIY replacement.
Replaced the rotary switch and fixed my problem. Read more
Replacement door hinge for electric and gas ranges. Supports door weight and ensures proper alignment. Needed when spring breaks or hinge arm cracks.
I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more
Oven won't shut off or temperature swings wildly? This control thermostat regulates heating elements to maintain set temperature. Easy DIY repair.
Well it wasn't hard to replace at all pretty easy. But trying to figure out what the problem was that got me. I turned of my oven and the light continued to stay on like it wasn't turn off but it was. I researched it and said it was the oven elements not true I was already confused enough so I said let go to the source of what make oven come on the oven control knob so I took the old switch off and looked up the numbers and ordered the part and lucky me that was the problem less than 50$ to fix... Read more
Seals your oven door to retain heat and maintain proper cooking temperature. Replace if torn, brittle, or heat escapes. Clips into place in minutes.
Ordered New Gasket and installed in about 3-4 Minutes. Only need small pliers to remove some of old clips from holes. New Gasket clipped in easily by hand. Read more
Range won't heat or display is dead? This oven control board clock regulates time settings and sends power to elements. Moderate DIY repair, 30-45 minutes.
I first checked the power , we had 220 volt at plug, I removed the back of the stove, checked things out , I found that the stove top burners still worked and the oven light worked. I tested and found that we had current to the timer and clock but nothing on the control worked to set the time, or to turn the oven on or to set the oven temp. I ordered this part on June 30th and received the next morning. I disconnected stove from electrical plug. Be Sure to unplug the stove for your... Read more
The Fan Blower is an OEM part for GE ranges and wall ovens. This part helps to circulate air within the oven cavity. The fan blower ensures that heat is evenly distributed during cooking, contributing to consistent cooking results, and prevents the electronic components from overheating, which could lead to malfunctions or reduced lifespan of the appliance.
Causes of damage to the Fan Blower can include accumulation of debris and grease, which can obstruct the fan and strain the motor, and mechanical wear over time that affects the fan's efficiency.
Symptoms of a bad Fan Blower in a range include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
I had to take the top panels off and two back panels off. Took off about thirty screws. It was very dirty and dusty inside so I took the lower panels off as well to clean and vacuum it. The hardest part was getting the double oven out of the cabinet. Overall it was very doable. Read more
Oven won't heat or both elements stopped working? A faulty thermal fuse cuts power to prevent overheating. Easy DIY fix with basic tools in under an hour.
Replaced the blown heating element. I also only to be on the safe side, replaced the over temp sensor. I checked it with the meter when I pulled it out and it was ok. Tested ok. Thank you very much for the less than 2 day delivery on the part. Read more
The Magnetron Thermostat is an OEM part for LG microwaves and built-in ranges. Its primary function is to monitor the temperature and ensure that it remains within a safe operating range. If the temperature exceeds the preset limit, the thermostat will interrupt the power supply to the magnetron, preventing overheating and potential damage.
Causes of a faulty magnetron thermostat can include electrical malfunctions, component failures, or physical damage. These factors can result in issues such as erratic heating, microwave not heating properly, or the appliance shutting off unexpectedly.
Symptoms of a bad magnetron thermostat may include:
This OEM LG part can also be used on Kenmore/Sears appliances.
Did some Google searches and most comments concerning this issue on LG stoves indicated the high temperature thermostat malfunctions when using the self cleaning function. This malfunction causes complete loss of power for the entire stove and locks the oven door. Since I wasn't completely sure if it was the thermostat or where it was for that matter, I called a service tech to troubleshoot the stove. He was able to determine it was the thermostat and further tested his findings by... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.