Need Help?
Call or text
Burner won't heat or cycles on and off? This infinite switch controls temperature levels on electric range surface elements. DIY repair in 10 minutes.
I ordered the correct part from AppliancePartsPros.com. When I received it, I opened the package and identified the parts I would need for my application. I cleaned up around my work space, then turned the power off to the appliance. I removed all the burners to get to the mounting screws for the range top. I then lifted the range top and supported it so I could see what I was working on . I first inspected all the wiring for breaks, or fraying. Then I moved on to the switch. Two screws... Read more
Burner won't heat properly or runs too hot? This infinite switch controls surface burner temperature. Common DIY fix takes 30 minutes with basic tools.
When I called customer service your representative at Appliance Parts Pros was able to help me diagnose the problem and order the two parts that I needed. both parts arrived the next day and with helpful tutorial videos I was able to replace both the Surface Unit Switch and the Universal Element in less than 45 minutes. Thanks so much for the great service and the money you saved me. Read more
Fix a microwave that runs but won't heat or won't start when door closes. This door switch is a common fix—most DIYers replace it in 15 minutes.
Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more
If your burner won't heat, stays on high, or only works on low, replace the infinite switch. Simple 20-minute DIY repair with just a screwdriver.
I was able to clean the Oven Temp Sensor with 99% alcohol. Then replaced All switches (after breaker was isolated). Put it all back the way I found it. Turned on breaker. Tested all functions and had no reports of Fan Code re-appearing since. Read more
Burners won't light or igniters click constantly? This igniter switch and wiring harness assembly restores spark ignition on gas range surface burners.
Replacing the bad harness switches with the new set fixed the problem. Read more
Burner won't turn off or heat properly? This range burner switch controls power flow to surface elements. Moderate DIY repair, 30-45 minutes.
We cut the power, took the control panel off, got the burner switch number from the original part, and ordered a new one. We were a little worried at that point, because your website offered a "replacement" part, with a different number than the original. However, we put the model number into your double check feature and were assured that we were getting the right part. The part arrived in two days and frankly we were still worried, because the new part was slightly larger than the original.... Read more
Burner won't shut off or stays on high? The infinite control switch regulates surface burner heat. Easy DIY repair, typically 10-15 minutes to replace.
Replaced the large burner control switches for the ones giving trouble. Since the other two switches had seen as much use as the faulty ones, replaced them too. After putting in new switches, found that one large burner had burned out so replaced it also. Range now cooks as good as new Read more
Burner won't turn off or stuck on high heat? This infinite switch controls surface burner temperature settings. DIY-friendly, 30-minute repair.
The problem seemed to be with the switch so I watched a few youtube videos to learn more about how ranges work. After locating the correct replacement switch I ordered it on-line around 10 pm Tuesday night. The new switch arrived Thursday morning at about 10 am and I had my range back up and working like new in less that 30 minutes. The hardest part was figuring out how to remove the slide in panel to access the switch. There were plastic washer/nuts behind each know which I was able to... Read more
Burner stuck on high or won't adjust temperature? This infinite switch controls heat levels on cooktop elements. DIY repair takes 1-2 hours with power off.
Based on internet search and data found on APPLIANCE PARTS PRO, I deduced that the "infinite control " module was most likely bad. Replaced it and all is good. Toughest part was remembering how to disengage cooktop from down draft blower and then pulling the cook top up in within it's opening. Once pulled up, I put short 2x4's across the opening corners to support the cooktop safely while I worked on it. Next issue was figuring out exactly which screws held the glass top in place. As... Read more
Burner stuck on high or won't heat? This infinite switch controls cooktop element temperature. Common DIY repair taking 30-60 minutes with basic tools.
Had to replace the switch for the left rear burner on a Whirlpool cooktop Model W5CE3625AB00. I turned off the circuit breaker for the cooktop and lifted it out of the countertop. It was simply held down by its own weight. There were approximately a dozen screws holding the smooth surface down onto the rest of the unit. I removed those screws, which allowed the cooking surface to lift back on a hinge in the back of the unit. Two of those screws were stripped, but I was able to remove them... Read more
Range burner won't shut off or heat properly? The infinite switch controls burner temperature. DIY-friendly repair takes about 15-20 minutes.
I ordered the infinite switch control from Appliance Parts Pro on a Wednesday afternoon and it arrived well packaged the next day even though I selected standard shipping. Thank you for the easy ordering and fast delivery! Replacing the old switch was easy: 1. Disconnect the power to the stove 2. Make sure the power is off to the stove 3. Pull 4 burner control knobs off and remove 4 large nuts attached to the 4 burner switches 4. Lift the face plate off and clean previously hidden cooking... Read more
Burner stuck on high or won't turn off? This burner control switch regulates heat settings. Moderate DIY repair—label wires before swapping.
If one control starts to fail the rest are sure to follow soon - so I replaced all four on our JennAir S160. Looked up the parts on line. Due to my background as an aviation electrician in the Navy and then working as an electrical systems designer for a defense contractor the toughest part was the clean up. Oh Well. Read more
Burner won't turn off or only heats on high? This infinite switch controls heat settings for your electric range's surface element. DIY repair.
I used your chat and found out the year my stove was made. He also told me what part to order as one of the burners had stopped heating up. We watched the video on how to install it. My friend installed it and my stove burner now works. Read more
If your dual burner only works on high or won't heat at all, this dual infinite switch kit restores full temperature control. Moderate difficulty install.
Replace dual infinity switch. The only difficulty is the terminal labels on the new switch did not match at all with the terminal labels on the original switch. The enclosed instructions were NOT helpful. But I contacted your representative, Johnny, and he was most helpful and patient. From my model number he located very specific and detailed instructions for how to wire the new switch. The rest of the job was easy. Your representative was outstanding. Thanks. Read more
Fixes burners that won't heat, stay on high, or make clicking sounds. Controls temperature settings on electric cooktops. Moderate DIY repair.
Put in a new infinite switch behind the knob to control temp level. Read more
Burner won't turn off or stays on high? This range surface element switch controls heat output. Easy DIY repair—most install in 5-10 minutes.
Installed new switches. Done in 20 minutes. Read more