Refrigerator Dispenser Parts

This drip tray sits beneath the grate area to catch grease and boil-overs, helping keep the cooktop cleaner and protecting components below. Replacing a bent, corroded, or missing tray restores proper fit and appearance. What it does:

• Collects drips, grease, and spills under the grate area
• Helps prevent liquids from reaching the burner box or wiring
• Supports correct placement of the grate/grill assembly
• Common symptoms: missing tray, heavy rust, warping, leaks or messes under the top

• 1 drip tray

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove the cooking grates/grill section to access the tray
• Lift out the old tray and position the new one with correct orientation
• Reinstall grates and verify proper seating and clearances before use

This dispenser facade replaces the outer trim pieces around your refrigerator's ice and water dispenser, restoring appearance and proper fit for smooth operation and sealing. It's a direct-fit cosmetic and protective assembly. What it does:

• Covers and protects the dispenser opening and controls from damage and debris
• Provides a finished look and helps direct water/ice into the cup
• Restores proper alignment when cracked, warped, or broken facade causes interference
• Helps prevent drafts and minor water splash at the dispenser area

• Disconnect power and shut off water to the appliance before servicing
• Many installations require removing the dispenser bezel and releasing snap-clips or screws; save hardware for reinstallation
• Handle plastic trim carefully to avoid scratches; use a soft pad when setting parts down

The Refrigerator Dispenser Lever is an OEM part for LG refrigerators. It is responsible for controlling and dispensing water from the door-mounted dispenser.

Symptoms of a bad dispenser lever include:

• Difficulty activating or inconsistent water flow when pressed
• Water dispensing without pushing the lever 
• Loose fit or wobbly feel
• Missing or broken lever pieces 

Causes of a bad dispenser lever can be wear and tear over time from frequent use. Exposure to impacts or damage during cleaning can also affect proper function.

This part is also compatible with select Sears/Kenmore models.

Replacement drip tray that collects and channels defrost and condensation water away from the cabinet to help prevent puddles and water damage. Sits under the freezer/drain area to guide meltwater to the evaporator or drain. What it does:

• Collects defrost and condensation water to prevent leaks and pooling beneath the appliance.
• Directs meltwater toward the evaporator/drain so it can evaporate safely.
• Helps reduce odors and ice buildup caused by standing water.
• Common signs you may need this part: water pooling under or behind the appliance, visible cracks or warped pan, or ice forming where water should drain.

• One drip tray

• Disconnect power before accessing the tray and remove any stored items from nearby compartments.
• Tray is typically accessed from the rear or behind the lower grille/panel—remove the appropriate access panel first.
• Inspect the drain channel for clogs or debris before installing the new tray and seat the pan flat to ensure proper drainage.
• Replace the tray if you see cracks, warping, or severe corrosion; use only manufacturer-recommended parts.

The Dispenser Funnel Guide Ice Door is an OEM part for Whirlpool refrigerators. It is responsible for guiding ice from the ice dispenser on the door into your glass.

A bad dispenser funnel guide ice door can occur due to regular use, wear and tear, or damage caused by foreign objects. If you notice ice not dispensing properly or falling outside of your glass, it may indicate a problem with the dispenser funnel guide ice door.

Symptoms of a bad dispenser funnel guide ice door include:

• Ice not dispensing into the glass or container properly
• Ice falling outside of the glass during dispensing
• Difficulty in activating the ice dispenser or inconsistent ice flow

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Drip tray that catches defrost and condensation water to prevent leaks and floor damage. Replaces a cracked or missing tray to restore proper water collection and reduce standing water beneath the appliance. What it does:

• Collects melted frost and condensation from the cooling system so water is contained and managed.
• Channels water toward the appliance's evaporation/drain area so it can evaporate safely.
• Helps prevent puddles and potential floor damage caused by a damaged or missing tray.
• Replace when tray is cracked, warped, leaking, or shows visible damage.

• Disconnect power to the appliance before performing any service.
• Access is typically through the lower toe grille or a rear access panel.
• Inspect mounting tabs and surrounding supports for damage and ensure the new tray seats properly.
• Wear gloves and take care around sharp sheet-metal edges during removal/install.

The Dispenser Drip Tray is an OEM part for Whirlpool refrigerators featuring built-in water dispensers. Located underneath the outlet spout, it collects any accidental water overflow or spilled cubes to prevent messes. 

Causes of a bad dispenser drip tray involve cracks interfering with its collection surface, or warping preventing it from fully guiding water into the pan below. Damage risks difficulties. 

Symptoms include:

• Water collecting outside the tray area on the cabinetry below
• Dispenser outlet jams from backflow during partial fills  
• Ice cube spills create a slipping hazard on the floor
• Increased effort required to avoid messes during dispensing

This OEM Whirlpool part is also compatible with some GE, Kenmore, and LG refrigerator models.

The Tank is an OEM part for Whirlpool washing machines. It properly dispenses detergent during the wash cycle.

Causes of a bad detergent tank can include: cracks, holes or other damage that cause leakage or improper detergent dispensing. Scaling or mineral buildup inside the tank over time may also lead to detergent dispensing issues.

Symptoms of a bad detergent tank include:

• Detergent not being fully dispensed or released during the wash
• Residue or leftover detergent remaining in the tank after cycles
• Clothes not getting properly cleaned due to insufficient detergent release

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Icemaker Fill Cup is an OEM part for Whirlpool bottom-mount and side-by-side refrigerators. Located inside the icemaker assembly, the fill cup sensor works to automatically detect when an ice scoop or bucket is in place below the icemaker chute. It signals the icemaker to drop ice cubes into the receptacle below.

Causes of a bad fill cup sensor can include mineral or dirt build-up inhibiting sensor response, moisture damage to its electronic functioning, or physical damage to the sensor head.

Symptoms of a bad fill cup sensor include:

• Ice failing to dispense or drop when a container is in place
• Ice clumping in the chute instead of dispensing properly  
• The icemaker continuing to run even with ice present below
• Inability to sense when ice is removed from the bucket

This OEM Whirlpool replacement fill cup sensor is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore bottom-mount and side-by-side refrigerators. 

The Refrigerator Dispenser Cover Assembly is designed to seamlessly integrate with your Samsung refrigeratorGÇÖs dispenser area. This cover assembly not only enhances the aesthetic of your appliance but also protects the internal components from spills and debris. Crafted as a genuine OEM part, it ensures a perfect fit and reliable performance, maintaining the integrity of your refrigerator. Installing this cover assembly is straightforward, allowing you to restore your dispenserGÇÖs functionality quickly and efficiently. The durable materials used in this assembly provide long-lasting protection, reducing the need for frequent replacements. By choosing this genuine OEM part, you can be confident in the quality and compatibility with a wide range of Samsung refrigerator models. Whether your original cover is cracked, missing, or damaged, the Refrigerator Dispenser Cover Assembly brings both practicality and style back to your kitchen. Improve your refrigeratorGÇÖs performance and appearance with this essential replacement part, designed with the customerGÇÖs needs in mind.

The Refrigerator Cup-Water Ice Maker is an essential component for maintaining the convenience and functionality of your refrigerator. Designed specifically for Samsung refrigerators, this genuine OEM part ensures seamless integration and reliable performance. The Cup-Water Ice Maker efficiently produces ice and chilled water, providing you with refreshing beverages at the touch of a button. Its durable construction guarantees long-lasting use, reducing the need for frequent replacements and saving you time and money. Installation is straightforward, allowing you to restore your refrigeratorGÇÖs ice-making capabilities quickly and effortlessly. By choosing this genuine OEM part, you can be confident in the quality and compatibility, ensuring your appliance operates smoothly and effectively. Whether youGÇÖre replacing a faulty unit or enhancing your refrigeratorGÇÖs features, the Refrigerator Cup-Water Ice Maker offers a practical solution for a better cooling experience in your home.