Refrigerator Ice Maker & Related

This automatic refrigerator ice maker assembly molds water into cubes and ejects them into the bin, restoring steady ice production. Replace a failed icemaker that no longer cycles, fills with water, or ejects cubes reliably.

• Freezes water in its mold and harvests finished cubes into the ice bin
• Controls the fill, freeze, and harvest sequence for automatic ice making
• Works with the refrigerator's controls to start/stop ice production as designed
• Common symptoms: no ice or low ice volume; won't fill; cubes won't eject; unit stalled mid-cycle

• Disconnect power and shut off the water supply before servicing
• Remove the ice bin; loosen mounting screws; unplug the wire harness; lift out the old assembly
• Transfer any brackets, covers, or fill cup from the original unit if required
• Align with the fill tube; secure screws; reconnect harness; restore power and water; allow up to 24 hours for full ice production

The Ice Container is an OEM part for Whirlpool refrigerators. It is responsible for holding and dispensing ice from the icemaker into the dispenser chute.

The ice container ensures the proper storage and convenient access to ice whenever you need it. It is designed to provide a reliable ice storage solution.

A bad ice container assembly can occur due to wear and tear over time or damage to the container or its components. If you notice symptoms such as the ice not dispensing properly, leaks from the dispenser area, or a broken or cracked ice container, it may be time to replace this part.

Symptoms of a bad ice container include:

• Improper dispensing of ice
• Leaks from the dispenser area
• Broken or cracked ice container

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cup fill spout directs the dispenser's water stream cleanly into a cup. If the spout is cracked, clogged, or warped, it can cause splashing or persistent drips—replacing it restores a steady, controlled flow.

• Funnels water from the dispenser outlet for a smooth, targeted stream
• Helps reduce splashing and water running down the door
• Can resolve drips after dispensing, erratic spray, or a damaged/missing spout
• Visible cracks, mineral buildup, or deformation are common failure signs

• Unplug the appliance and turn off the water supply
• Open the dispenser area and release the spout from its locking tabs or clips
• Seat the new spout fully; transfer any seals from the old part if applicable
• Restore water and power, then test for proper flow and leaks

PLEASE NOTE: Due to manufacturer changes, the auger is now metal

The Ice Container is an OEM replacement part for Whirlpool refrigerators. It is responsible for storing and dispensing ice from the refrigerator's ice maker.

A bad ice bucket assembly can occur due to wear and tear, cracks, or damage to its components. If you notice symptoms such as a broken or damaged assembly, difficulty in dispensing ice, or leaks from the ice maker, it may be time to replace the ice bucket assembly.

Symptoms of a bad ice bucket assembly include:

• Broken or damaged assembly
• Difficulty in dispensing ice
• Leaks from the ice maker

Restore your refrigerator's ice maker by replacing the faulty or damaged ice bucket assembly with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement plastic ice scoop makes it easy and sanitary to transfer ice from the bin to glasses or trays. Durable, lightweight design restores convenient ice handling after the original scoop is lost or worn. What it does:

• Provides a hygienic way to scoop and serve ice without using hands
• Fits standard refrigerator ice bins and buckets for easy access
• Helps prevent spills and keeps ice contained while serving
• Replaces missing, cracked, or discolored scoops to restore everyday use

• No tools required — simply place scoop in the ice bin or store in a convenient location
• Wash before first use and after each use with warm, soapy water
• Keep away from high heat to avoid warping or damage
• Not an electrical component; disconnecting power is not required for replacement

The Ice Maker (12 cube) is an OEM part for LG refrigerators. It is responsible for producing ice cubes, typically in batches of 12, and dispensing them into the ice bin for easy access. This ice maker ensures a consistent supply of ice, ideal for everyday use and entertaining guests.

Over time, the ice maker can become faulty due to regular wear and tear, mineral buildup from water, or issues with the internal components such as the motor or the water inlet valve. A malfunctioning ice maker can lead to inefficient ice production or no ice at all.

Symptoms of a bad ice maker include:

• The ice maker not producing ice
• Smaller than usual or misshapen ice cubes
• Leaks or water overflow in the ice maker compartment
• Unusual noises during the ice-making process

This OEM LG part is also compatible with Sears/Kenmore models.

The Ice Bucket Assembly is an OEM part for LG refrigerators. It is designed to collect and store ice produced by the icemaker, ensuring a convenient and organized storage solution within the freezer.

Causes of a bad ice bucket assembly can include damage from frequent handling, cracks or breaks due to impact, or issues with the internal components such as the auger or motor. Over time, these issues can impair the functionality of the ice bucket, leading to inefficient ice storage or dispensing problems.

Symptoms of a bad ice bucket assembly include:

• Cracks or visible damage to the bucket
• Ice not dispensing properly
• The bucket not fitting securely in place
• Excessive noise during ice dispensing

This OEM LG part is also compatible with Sears/Kenmore.

The Ice Maker and Auger Motor Assembly is an OEM part for LG refrigerators. This assembly is responsible for both producing ice and dispensing it from the ice maker. The ice maker produces ice cubes, while the auger motor drives the auger to move ice from the ice bin to the dispenser chute, ensuring a steady flow of ice whenever needed.

Causes of a bad assembly can include electrical issues, wear and tear from regular use, or damage to the motor or ice-making components. A malfunctioning assembly can lead to inconsistent ice production and dispensing problems.

Symptoms of a bad ice maker and auger motor assembly include:

• No ice production or insufficient ice
• The auger not dispensing ice properly
• Unusual noises from the ice maker area
• Ice jams or clumps in the ice bin

This OEM LG part is also compatible with Sears/Kenmore models.

The Icemaker is an OEM part for Whirlpool refrigerators. This component is responsible for producing ice by automatically filling with water, freezing it, and then ejecting the ice cubes into the storage bin. Please note that for installation, you will need to reuse the original cover and bracket from your existing icemaker. Makes 5 cubes at a time.

Causes of a bad icemaker can include mechanical failures, clogged water lines, or electrical issues. Over time, wear and tear from constant use or exposure to hard water and impurities can also affect its performance.

Symptoms of a bad icemaker include:

• The icemaker not producing ice
• Ice cubes being smaller than usual or misshapen
• Leaking water inside the freezer
• Unusual noises during the ice-making process
• The ice bin not filling up

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Ice Maker Assembly is an OEM component specifically designed for LG refrigerators. It is responsible for automatically producing batches of ice cubes through an electrical freezing process.

Causes of a bad ice maker assembly can include failures in the electrical components, freezing properties deteriorating over time, or physical damage to the assembly housing. 

Symptoms of a bad ice maker assembly include:

• No ice production or very slow icemaking  
• Cubes that are improperly formed or jammed inside the unit
• Error codes displayed related to the icemaker
• Leaking or water issues around the assembly area

This LG part is also compatible with Sears/Kenmore models utilizing the same refrigerator chassis and components.

Note: The icemaker does not include the harness or the shut off arm.

This ice bucket assembly stores and delivers ice to the dispenser. Replacing a damaged bucket restores smooth, reliable dispensing and helps prevent jams when the original container is cracked, worn, or no longer engaging the drive.

• Stores finished ice beneath the icemaker and positions it for dispensing
• Interfaces with the dispenser drive to move ice into the chute when activated
• Helps maintain proper alignment for consistent cube delivery
• Common symptoms: cracked or broken container/tabs, ice won't dispense or jams, grinding/skipping during dispense

• Disconnect power to the refrigerator before servicing
• Remove the old bucket; empty ice and note the drive coupler orientation
• Seat the new assembly fully so the drive engages; transfer any reusable covers from the original if needed
• Restore power and test ice dispensing