Need Help?
Call or text
Refrigerator shelf frame that supports glass or wire shelves inside the fridge. Replace if cracked, broken, or warped to restore proper shelf support.
No instructions are included with either piece, which makes installation take more time and care. Tools needed: Small standard flat blade screwdriver, box knife or other knife with at least a 2" long blade, super glue. Remove the old main crisper frame: 1. Remove old main frame by lifting upward and outward. 2. Remove the center rail from the frame. May require bending of the main frame to remove it. 3. Remove the crisper front panel by unsnapping from frame. This is easily done by... Read more
Upper freezer door bin for side-by-side refrigerators. Installs above ice chute. Replace if cracked, broken, or missing. Measures 13"L x 5.5"W.
Ordered part from appliancepartspros.com and got them within 2 days.that was great,refrigerator is like new again,am I am pleased with service and there swift delivery. If I need any thing else,there is only one place I will get them.from. Thanks! Read more
Replace your refrigerator's interior light bulb when it burns out to restore visibility. Easy screw-in installation. Verify fit with your model number.
Put a new one in an easy fix but a hard bulb to fine Read more
Stores and supplies water to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged from mineral buildup or freezing.
Replaced tank assembly. Actually I think the supply hose was originally not fully seated in the tank and I think I could have re-seated it deeper through the gray bushing. When I set the line into the new tank, still leaking. Pulled out supply line and reset using a little more force and line went into the tank. Took the bushing clip off the other tank and used it for the supply line bushing. So far, no leaks. The thing to remember is to push the edges of each hose bushing inward to pull... Read more
Replacement glass shelf for refrigerator interior storage. Installs in shelf frame to hold food items. Order if original is cracked, shattered, or broken.
I took apart the old bucket with a screwdriver and put the new one with no problems. Read more
Protective washer that sits between the door hinge and frame. Replaces worn or missing washers that cause door sagging, dragging, or poor seal contact.
My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more
Replaces cracked, broken, or worn water and ice dispenser control panel on your refrigerator door. Installs at dispenser recess with mounting screws.
Replaced faceplate of refrigerator. Read more
Refrigerator freezing food? A faulty damper assembly causes constant cold air flow to the fresh food section. DIY-friendly repair, under 1 hour.
I went on line and read your advice page. Based on that, I removed the damper assembly (six screws counting the miserable light fixture) and found the damper door broken as predicted. I went back to your page and ordered the new part. Nice breakdown to get number. After that, I disassembled the damper assembly, found that the ABS plastic damper had broken from the actuator probably as a result of fatigue from cycling back and forth for twelve years. I used super glue to re-attach the damper... Read more
Ice maker stopped making ice or freezing into a solid block? This ice maker assembly restores function in 15-20 minutes with just a screwdriver.
Purchased both the ice maker assembly and the valve assembly to replace the parts as needed. replaced the ice maker assembly first, and this fixed my problem. Took about 10 minutes, mainly because I didn't watch the YouTube video first. Had I watched that, it would have probably taken even less time. One Philips head screw driver is all you need. Read more
Replace your cracked or broken refrigerator drawer glide. Mounts to the interior wall to support smooth drawer sliding. Essential for worn or damaged glides.
Ordered and installed new ones. Read more
Seals the ice chute assembly in your refrigerator's dispenser door. Replace if cracked, broken, or missing to prevent frost buildup and air leaks.
Replaced chute gasket and ice bin. Has worked great so far. Fingers crossed. Read more
Creates an airtight seal around your freezer door to prevent warm air entry and cold air loss. Replace if torn, cracked, or not sealing properly. Verify fit by model number.
Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more
Creates an airtight seal to keep cold air in and moisture out. Replace if torn, worn, or causing the door to pop open. Confirm fit with your model.
Previous tenants damaged the refrigerator by ripping the gaskets out and breaking the glass shelf over the veggie-drawers. I tend to replace things instead of fixing them, but AppliancePartsPros made it so easy to find parts. The gaskets and glass were specific to my make and model. Easy to install and worked perfectly. Definitely a win! I plan to do the same type of repair work to the dishwasher next. Read more
Drawer glide for refrigerator deli or crisper drawers. Replace if cracked, broken, or causing drawer to stick or fall out when opened. Mounts to shelf.
Ice won't dispense from your refrigerator door? A cracked bucket or broken auger is often the cause. This assembly restores ice dispensing function.
Replaced the ice tray. Read more
Fix no water or ice, leaking valve, or slow water flow from your dispenser. This refrigerator water inlet valve is a straightforward DIY repair.
First I replaced the filter thinking it was the problem, but that was not the case. Next was replace water supply valve at the back of the refrigerator. It was very easy. The only thing that was in question was how to get the refrigerator side line off of the existing valve. There is a plastic slide clip that you remove and pull the line out and press the line back into the port it came out of. It was a very simple project and took about 20 minutes. Read more