Refrigerator Parts

I replaced it. Read more

Having never fixed a fridge before, I did a little research. The unit was not old & the cooling system was operating. Observing the frozen ice inside, I diagnosed it as the heat rod and/or it's thermostat as bad. I contacted ApplianceParts Pros, who assisted in confirming my theory. IMPORTANT NOTE: the sales advisor Joyce was truly an intelligent, knowledgable professional, NOT some "burger-order taker" usually encountered. This alone speaks VOLUMES. Subsequently, the parts arrived... Read more

• Ice maker not making ice
• Leaking

Replaced inlet water valve Read more

Replaced the defrost thermostat and heater and the refrigerator was working again. Read more

Replaced gasket. Read more

Replaced the defrost thermostat in freezer and fridge and the defrost heater in freezer. These guys had my parts in stock and I got them in 2 days Read more

First, I removed the old gaskets, which was a very easy task since they are held in the doors by rubber beads in recessed slots. I installed the new right door gasket in less than 10 minutes by gradually pushing the retainer bead into the door recessed slot with finger pressure until it was seated properly. The left door bead was somewhat more difficult to install into the bead slot, because the recessed bead slot is covered by a hinged flap on its left edge that doesn't permit easy access.... Read more

• Freezer not defrosting
• Fridge too warm

Toughest part of this repair is figuring out how to get things apart. Amana doesn't provide you a repair manual showing how to disengage the various plastic covers. Initially disassembled the bottom freezer compartment so I could get to the evaporator coils; they were completely frozen in block of ice, restricting air flow to the fridge above. Obviously, the auto defrost cycle had not been running, or was short-cycling. Manually defrosted. Found this link for running diagnostic tests on the... Read more

1.) Located where the water leak was coming from in the refrigerator. 2.) Unplugged the refrigerator. 3.) Shut off the water supply to the refrigerator. 4.) Unscrewed the back cardboard panel. 5.) Unscrewed the Water Valve attached to the side of the refrigerator (one screw). 6.) Disconnected the three electrical plugs on the water valve. The plugs are different sizes so there is no need to worry about reconnecting incorrectly. 7.) Disconnected the two water lines by pushing down on... Read more

Initially I noticed the crusher drum was cracked and broken so I replaced the drum the retaining nut on the end of the auger and the circlip and washer. it worked fine for a time and then the drum began free wheeling. upon further inspection I discovered the retain nubs on the auger had worn down allowing the blade to slip down the auger body. so I replaced the auger, drum, drive blade, and drive cam. I recommend if you gave a problem with the ice dispenser you break down and inspect the entire... Read more

Yes exact fit Read more

Replaced the gasket. Five minute repair after door removal. Working great now. Read more

Got the six year old refrigerator from my daughter because of it freezing up but was in good ( Stainless Steel) shape to replace our 21 year old Kitchen Aid. The thermistor had been replaced as a cheap first step but didn't correct the problem as it totally froze over within five days. I decided to tear down again and check the defrost heater element which was found to have an open circuit and hence the replacement part. Thanks to AAP, I ordered the part at the weekend, was shipped on Monday... Read more

Put racks to together and put into fridge Read more

Replaced both The electrical board I found under the fridge was very easy to replace. The fan motor took a minute to bed puns and the biggest challenge was taking off/on the back panel to get to it. (By the way it was located in the freezer section. take drawers out to get to it. Read more

Replaced broken handle support bracket (part #AP5620448) and cap (part #AP5620751). Used a phillips head screwdriver and allen wrench. Pliers also came in very handy. If replacing cap and support bracket, be sure to install cap before support bracket, otherwise you'll have trouble installing the cap. I ended up not needing to replace the fixer handle (part #AP4372038), but I'll keep it around just in case. Read more