Roper Parts

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more

Used U-Tube diagnostic clips to diagnose that most likely problem was a worn Evaporator Fan Motor which is located in the freezer back wall, located in the top third of the unit. I removed 6 hex head screws from the freezer's interior back panel that covers the evaporator coils. The cover is located in the lower 2/3s of the back wall. Removed all shelving. Also removed screws that held in shelf supports on one side of the freezer wall. I then removed the back panel. You may need to... Read more

Replaced internal drain hose. and while I was in there I changed some known wear items. water pump,direct drive coupling tub to pump hose and a spring Read more

I located the web site via the internet and contacted the 1-800 number. The service rep was incredibly helpful and personable. After providing her with the model number and parts needed,the process could not have been easier. My replacement parts arrived the next day a perfect match. I highly recommend using this service, first class all the way. Read more

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

• Will not dispense detergent

I ordered a new soap dispenser and began a new venture in repairing my dishwasher. I turned off the breaker that suppled power to the unit. I removed all the T-15 torx screws from the inside cover except one, which my wife helped me hold in. This prevents the cover from dropping off. Then, after removing those two, we closed the dishwasher cover, and lifted off the outside cover. That being off, I saw the two wires connecting the dishwasher dispenser solinoid. Removed them. Notice, that one... Read more

Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more

First unplug or turn off the electrical breaker to the dishwasher. Then I removed the phillips head screws holding the inner door to the outer door panel. I then removed the hex head screws holding the dispenser assembly. The electrical connection needs to be disconnected and then reverse the procedure to install the new dispenser. Restore power to the dishwasher and your done. Read more

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

The drip pans I ordered fit my stove perfectly. I was extremely happy. I had tried drip pans from Wal Mart and Lowe's and they wouldn't sit right in the stove. Read more

Purchase a new one and installed per your video on Youtube. Great and easy. Read more

Took off cover, installed new parts. Read more

By replacing it Read more

Bought new Transmission/gear box. Putting in the new one was easy. Taking the old one out was a nightmare. The corrosion on the spanner nut and drive block was awful. Ten years of VERY hard water and six kids made for a lot of corrosion and hard water crystallization. I do not own a spanner wrench. I am not sure having one would've helped. I tried pipe wrenches, needle nose vice-grips and many other ways. What eventually worked was taking a three inch ratchet extension, putting it... Read more

Remove and replace Read more