Roper Parts

• Won't start
• Fridge too warm

Took access panel off the back of the refrigerator with 1/4 inch nut driver and found that the compressor was not running properly (humming and hot but not compressing). The compressor cooling fan was working as well as the fan in the freezer compartment. I fixed the same problem with another refrigerator by replacing the relay and start capacitor on the compressor. I pulled these two items from the compressor connector (gently pry the brown part from the comp terminals first and then the... Read more

Replaced filter housing, and both water tubes Read more

Replaced set of three springs. Read more

The parts I purchased from Appliance Parts Pro fit perfectly and were reasonably priced. I received them the next day, which made the Wife (and me) very happy. Although Appliance Parts Pro did not have a repair video for this, I was able to find one online and the machine is washing like new again. The website is well laid out and easy to find what your looking for. Between the available parts and the videos they provide, anyone who is reasonably handy should be able to repair their machine as... Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Buy a new door shelf bar! I ordered it and two end caps (I didn't know the things existed) and shortly the package came from Appliance PartsPROS.com. In a matter of minutes I had a shiny new shelf bar and vavoom the refrigerator was as good as new! No more juice, milk, or soda cleanup on the floor! Thanks for your good service with the video, also. Read more

Instructions are very dumb, but it's an easy fix. Loosen all the nuts that hold the metal bars that hold the old gasket. (Loosen. Don't take them off!) Pull off the old gasket. Slip the new into place all the way around. Get the corners in position, middles can be loose. Tighten the corners, then work the middles into place and tighten as you go. Done. Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Watched the video and completed repair as shown Read more

I first DISCONNECTED POWER FROM THE RANGE using the breaker. I then pulled the range out from the wall to give myself plenty of working room. I lifted the range top up as when you clean under the burners. I then moved the ends of the bottom of the slide rods that lock the range top open back where they came loose from the top of the range. This allows you to fold it higher and have complete access to the top of the range. I then took out all the Phillips head screws that hold down the sheet... Read more

The auger would not turn the dispenser because the screw threads were stripped. I could not re-thread it so I had to replace the entire motor assembly. The video your company provided was extremely helpful not only for fixing the problem but to give me the confidence to do it myself. It was a very detailed video that included all the safety instructions. Read more

Simple unplug, unscrew and replace. Read more

• No heat

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only... Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

We bought replacement parts from you and my daughter fixed it. It is working now. It would have been nice if all the parts came in a set. Read more