Samsung Parts

Once I found the hole for the spring arm to go in it took 1 min. Tip: make sure the spring is on the left side pin and, insert it First to insure the spring aligns then use a screw driver to pry out the Right side flange slightly to aide in inserting the right side pin into its hole Read more

• lights flashing or blinking

Since my Samsung Dishwasher would not drain and had a flashing quick light, I removed the racks and both spray wands. Which allowed me to remove the lower screen assembly. This revealed a worn and broken check valve and broken grinder blade. I cleaned the inside of the dishwasher and removed the unit from under the counter. I removed and cleaned the brake assembly ( large transparent plastic section on left side of the dishwasher). I cleaned this for preventive maintenance by taking the float... Read more

Took out the original and put in the replacement. Read more

• Ice maker won't dispense ice

I read an article concerning the same problem and ordered the interior lever, but the real issue was that the plastic piece that activated the water flow was broken off the interior of the water dispenser cover assembly. I popped out the dispenser cover (it is on very snugly) and replaced it with a new one (again, it went back on but with some force needed). I only needed a screwdriver to pop the cover and would suggest you use a towel as a buffer to prevent scratching the interior of the... Read more

Replaced filter. Read more

I got it in the mail, I opened it, I handed it to my wife....and she installed it. Easy-Peasy! (Being retired is a blast) Read more

• Frost buildup
• Doesn't shut off

Ordered parts, defrosted refrigerator, and replaced with new items. This problem has been going on quite some time, while Samsung refused to acknowledge the defective unit, claiming it was owner fault. The defrosting had to be completed every 3-4 months and managed in time to require defrosting every few days. Originally a repairman came and although he defrosted it the first time, he informed us, this is quite common and the unit is defective by design; which is why we continued to defrost on... Read more

Unplugged the stove. Removed the back of the control panel. Removed and replaced the membrane keyboard and the main PCB. Reassembled the stove and everything was back to normal. The PCB was probably ok but I wanted to be sure and get the stove working as soon as possible so I replaced both parts at the same Read more

Normally when you let go of the dishwasher door partly open it would stay in that position. But lately when you let go of the door it would fall to the fully open position. Turns out this little cable was broken one one side. Just puss the dishwasher slightly out of the cabinet and you can replace the cable in minutes. It is just held in place with a spring. Read more

Replaced board. Parts were as described... OEM replacement. Fast shipping. Wife got he range back in record time. Have protection plan with lowes. They said it would be 2 weeks before a service tack could come out and diagnose problem. Then more time to get part and install. So... did it myself! Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

Unscrewed old flap. Then unplugged it. Plugged in new flap ( make sure it is right side up). Screw both hinges back, and voilà, fridge fixed! Read more

I replaced the two affected burners, and the problem was solved. Read more

I replaced the control board and the microswitch. Read more

Knowing from a previous repair, that there was only 3 parts that could be bad. I decided if I was going to take it apart to change all 3. Not having the proper test equipment, it was cheaper to replace the 3 parts than pay a repair person. Read more

• Too hot
• tripping breaker

I found the assembly with heater element, thermostat, and the thermal fuse already assembled (cheaper than finding what part was bad and ordering that one part). unplugged dryer, pulled it out and removed the dryer exhaust tube, the top and front. The harness was a little short so I wasnt able to pull the whole heater assembly out before disconnecting. BEFORE disconnecting I took a picture so that if my brain forgot what wires went were!!!! put the dryer back together and put a load that just... Read more