Samsung Parts

First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more

• Ice maker not making ice
• Ice maker dispenses too much ice

I replaced the ice maker assembly was pretty simple process Applianceparts made it easy and even told me they would take the part back if it wasn't the problem. Read more

• Door latch failure
• Will not agitate

After watching the video it was strait forward. Just Pull the screws pop the lid swap the springs "grease them" and put it back together. I would suggest that you have a person help you mostly has a second pair of hands. The lid was over rear springs and it will save you some expletives to have the extra body. I had worn out springs and the load kept becoming unbalanced during spin cycles I just happened to coincide with the Lock mechanism failing. The motor drive for the lock stopped working.... Read more

Ordered a new leg from Appliance Parts & put it on. Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

I bought the defrost-clip (clip-drain-evap), but once I took the refrigerator apart--the large plastic "back" had frozen to the rest and left the insulation in pieces when I tried to pull it apart. I was able to replace the clip-drain-evap piece with little trouble once the ice had melted, but I was unhappy with the looks of the "back". So I ended up ordering a new "back"(Yassy cover-evap) that included the new insulation as it's made in one unit. Once it arrived, replacing the new "back"... Read more

• Leaking

I just had to pull the old out and push the new one in. Read more

Replaced the igniter. This was a relatively simple process. Read more

• Oven not heating evenly
• temperature not accurate

First I did a search for my model stove, I read the discriptions of what it was doing and came to the conclusion it was the fan motor. I then called an appliance dealer in my local area to find out that the fan motor cost all most double what I could get it online. I called to see how much it would cost to have a repair man come out and fix it, which would have cost 260 dollars. So in one of the suggested comments that someone previously left it stated that it could be done in about 20... Read more

Removed refrigerator panel, disconnected light and fan power. Removed fan assembly and replaced motor, grommets and fan attachment spring. Unit had adhesive on spring to help hold the spring. Chatted with customer service and clarified that spring and fan would easily pull off motor shaft. Adhesive probably was extra measure used during original build of the fridge. Noise was due to fan rubbing on housing. New fan position set to avoid any rubbing. Read more

Ordered new ice maker from AppliancePartsPro.com. Removed about 8 screws holding the icemaker and the panel behind the icemaker. The electrical connection (10 pin plug) is behind the plastic panel. Attached new icemaker cable, reinstalled screws, crossed fingers, and now I have ice. Read more

I simply ordered a new vent online with Appliance Pros.com and received the new part within a few days. Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

• Will not stop filling with water

This error code indicated faulty water level and wash cycles were exhibiting either no water or too much water. Saw utube vid using this part for this type of problem and so far the repair is working well. Part arrived in 2 days, it was the right part and the machine is working the way its supposed to so I'm very happy. The worst scenario would have been to hire a repair guy to rip me off for a "Johnson Rod" I didn't need. Read more

• Leaking
• Not dispensing water
• Noisy

Verified that the water line had flowing water, check. Removed lower screen and vacuumed and cleaned all dust. Proceeded to test water flow to the valve and beyond the valve. The valve did not allow water to pass through it. Nor would it open or close. Went to Marbeck for confirmation and was sent to your website for the part. Read more

Removed old lint filter cover. Inserted spring on one end of lint cover and installed cover. Read more