Thermador Parts

Keep your appliance's controls working reliably with this switch cover. It mounts over a switch to hold it in place and shield it from damage, helping ensure consistent actuation and long service life.

• Retains and protects a control/interlock switch within its housing
• Helps keep the switch aligned for reliable on/off detection
• Shields the switch from dust and incidental contact
• Cracked, loose, or missing cover can cause intermittent operation or no response when the control is pressed

• Disconnect power to the appliance before servicing
• Remove the necessary panel to access the switch; note wire positions/orientation
• Transfer any clips/screws from the old cover and seat the switch fully
• Secure wiring away from pinch points before reassembly

Replacement rubber feet for gas cooktop grates. Kit includes 4 feet and adhesive. Needed when original feet are cracked, worn, missing, or fell off.

Refrigerator not cooling or making rumbling noise? A faulty evaporator fan motor prevents cold air circulation. DIY-friendly repair restores even cooling.

Replacement water feed tube that delivers water to the upper spray arm in your dishwasher. Replace if cracked, split at seams, or leaking due to wear.

Protective cap that mounts over control switches on your range hood control panel. Replace if cracked, broken, or missing to keep switches properly aligned.

This is a spark ignition switch used on a range or cooktop that controls the electric spark to ignite the surface burners when the control knob is turned. It connects to the burner igniter circuit and signals when to fire the spark module. Replace this switch if your burners won't ignite, the spark clicks continuously even after the flame is lit, or the igniter fails to spark when the knob is engaged.

This is a gas tube or connector used in a range or cooktop to route gas from the supply line to the burner assembly. It ensures a secure, leak-free connection for proper gas flow. Replace this part if you detect a gas smell near the appliance, experience uneven flame, or notice visible damage or corrosion on the existing tube.

This meat probe sensor is a temperature-sensing device that inserts into food while it cooks in the oven, allowing the oven to monitor the internal temperature and automatically stop cooking when the target temperature is reached. It connects to a jack inside the oven cavity via a heat-resistant cable. Replace this probe if your oven no longer reads the food temperature accurately, displays a probe error code, or if the cable or tip is visibly damaged.

This pressure chamber is part of the water level sensing system in the dishwasher. It connects to the tub and the water level sensor, using air pressure changes to detect how much water has filled the machine so it knows when to stop filling. Replace this component if the dishwasher overfills, underfills, or displays water level error codes during a wash cycle.

The Circulation Pump Assembly is an OEM component specifically designed for Bosch dishwashers. It is responsible for circulating water during the wash cycle and helping dishes get properly cleaned. 

Causes of a bad circulation pump assembly can include normal wear and tear, as well as damage from debris getting caught in the pump mechanism over time. 

Symptoms of a bad circulation pump assembly include:

• Inability to circulate water, resulting in poor wash performance  
• Loud noises or vibrations coming from the pump area
• Leaks around or below the pump housing

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. Replace yours today to restore optimal water circulation for thorough yet gentle cleaning.
 

Red indicator lens for gas cooktop burner controls. Replace when cracked, discolored, or missing to restore burner status visibility. Verify long vs short lens for your model.

Oven not heating or baking unevenly? This bake heating element restores consistent heat. DIY-friendly repair takes about 15 minutes with basic tools.

Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

The Range Hood Halogen Lamp is an OEM part for Bosch range hoods. It provides illumination for the cooking area beneath the range hood, enhancing visibility while cooking. This halogen lamp is designed to fit seamlessly into the range hood, ensuring a bright and focused light.

You should replace this halogen lamp if it burns out or becomes faulty. Causes of a bad halogen lamp can include filament burnout from prolonged use, electrical surges, or damage from handling during cleaning or maintenance.

Symptoms of a bad halogen lamp include:

• Dim or flickering light
• No light when the range hood is turned on
• Discoloration or dark spots on the lamp
• Frequent bulb replacements needed

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.