Wall Oven Heating Element

This surface heating element restores reliable heat to an electric cooktop burner so pots and pans warm evenly and predictably. Replace a failed element to bring consistent performance back to your range or smooth-top cooktop.

• Supplies heat to a single cooking zone on an electric range or glass-top cooktop
• Replaces an element that is open, shorted, or intermittently heating
• Common symptoms: burner won't heat, heats unevenly, or only part of the zone glows
• Helpful when there is visible damage or hot spots on the element

• Disconnect power at the breaker; allow the cooktop to cool completely
• Access the element by lifting/removing the cooktop or from below
• Move wires one at a time to matching terminals; reuse any mounting clips/brackets as required
• Support the glass top during service and avoid stressing or scratching the surface

This 8-inch surface element restores reliable heat to the large burner on an electric range. Replace a worn or open coil to bring back fast, even cooking performance and consistent temperature control.

• Heats cookware on the large 8-inch burner of coil-top electric ranges
• Common symptoms: burner won't heat, heats intermittently, or needs "wiggling" to work
• Visual clues: broken coil, blistering, hot spots, or arcing/burn marks at the terminals
• Helps ensure even heat distribution and stable pan support

• Disconnect power at the breaker and allow the element to cool completely
• Lift the old coil slightly and pull straight out from the receptacle
• Inspect the element receptacle and wiring for heat damage; replace if burnt before installing
• Align terminals and support feet, then push firmly until the element is fully seated

This bake element restores even, reliable heat in the lower oven during the bake cycle. Replace it if the oven won't heat, struggles to reach temperature, or the element shows visible damage.

• Provides the primary heat source for baking in the lower oven cavity
• Common symptoms: no heat in bake, slow preheat, not reaching set temperature, uneven baking, or visible blistering/burn spots on the element
• Converts electrical energy to radiant heat for consistent oven performance

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks; take out element mounting screws and gently pull the element forward
• Support and transfer wires one at a time to the new element; ensure tight, secure connections
• Reinstall, restore power, and test for proper preheat and even heating

Restore consistent baking performance with this lower-oven bake element assembly. It replaces a failed element so your oven can preheat correctly and maintain even heat during bake cycles.

• Provides the primary heat source in Bake mode
• Works with the oven controls to reach and hold the set temperature
• Common failure symptoms: no heat during Bake
• Extended preheat times or undercooked results
• Visible damage such as blistering, cracks, or breaks in the element

• Disconnect power at the circuit breaker before servicing
• Remove oven racks; take out element mounting screws and gently pull the element forward to access terminals
• Transfer one wire at a time to the new element; prevent wires from slipping back into the oven wall
• Ensure terminals are fully seated and the element is secured before restoring power

Restore reliable top heat for broiling and browning. This replacement broil heating element brings your oven's broil function back to full strength so foods brown evenly and the broiler heats when selected.

• Provides high, direct heat from the top of the oven during the broil cycle
• Helps with top-browning in some baking/roasting modes
• Common failure signs: broiler won't heat or glow, uneven browning, visible breaks or blistering on the element
• Often tests "open" (no continuity) when failed

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, then gently pull the element forward and support the wires
• Label and transfer wires to the new element one at a time; do not allow wires to slip back into the rear cavity
• Reinstall screws, ensure secure connections, restore power, and test the broil function

The bake element is the lower oven heating element that produces heat during bake cycles. Replacing a failed element restores proper preheating and even baking performance when your range no longer heats correctly in bake mode.

• Provides bottom-up heat in bake mode to reach and maintain set temperatures
• Typical symptoms include no heat in bake, excessively long preheat, or uneven/undercooked results
• Visual clues of failure may include blisters, cracks, or burnt spots on the element
• A shorted element may trip a household breaker when energized

• Disconnect power at the breaker before servicing; verify no power to the range
• Remove oven racks; unfasten the element from the rear wall and gently pull it forward to access terminals
• Transfer the wires to the new element one at a time; do not let wires retract into the rear panel
• Reinstall and secure the element, ensure connections are fully seated and clear of metal, restore power, and test

Size: 8 inch. 2200 watt. Radiant.

The Heating Element is an OEM part for LG ranges. It is responsible for providing heat to the oven cavity, allowing for proper cooking and baking. 

The heating element is exposed to high temperatures with each use and over time can become brittle or defective. Causes of a bad heating element can include cracks in the coils, burn marks, or faulty electrical connections. 

Symptoms of a bad heating element include: 

• The oven not heating up or heating unevenly
• Diminished cooking power 
• Burning or burning smell from the oven
• Tripped circuit breaker or blown fuse

Replace yours today with this genuine LG heating element and restore your oven's full cooking capabilities. This OEM LG part is also compatible with Sears/Kenmore.

This lower bake element restores consistent bottom-heat for proper baking and preheating in electric ranges and wall ovens. Replacing a failed element helps eliminate undercooked centers and uneven results.

• Provides primary bake heat from the bottom of the oven cavity
• Common failure signs: no heat in Bake mode, very slow preheat, uneven baking, or visible damage
• Helps ensure stable oven temperatures when paired with a working broil element and thermostat
• Direct-fit replacement designed to connect to existing wiring and bracket mounting

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, gently pull the element forward, and transfer wires one at a time to the new element
• Avoid stressing or loosening terminal connections; secure the bracket firmly
• After reassembly, restore power and test Bake to verify proper operation

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

Note: Size 8 inches

The Element is an OEM replacement part for Bosch electric ranges. It generates the heat needed for baking, broiling, and other cooking functions.

Causes of a bad element can include mineral buildup interfering with heat transfer, melted or burnt connectors from overheating, or damage from impact over time. 

Symptoms of a bad element include:  

• Inconsistent or incomplete heating of the appliance
• Long preheat times or inability to reach desired temperature  
• Burned food indicating insufficient or uneven heat
• Safety issues such as sparking or smell of burning

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This surface heating element restores reliable heat to a cooktop burner. Replace a failed or damaged element to bring back even, responsive heating performance and consistent temperature control for everyday cooking.

• Converts electrical power into heat for one cooktop burner
• Common fix for a burner that won't heat or only heats intermittently
• Can address uneven heating or erratic cycling at a set temperature
• Appropriate when the element shows visible damage or burned spots

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access varies by model; lifting the cooktop or removing the glass top may be required
• Handle the element carefully and avoid stressing the heating surfaces
• Move wires one at a time to matching terminals; ensure all connections are secure before reassembly

This 8-inch Haliant radiant surface element mounts beneath the glass of a smooth-top range to heat a single cooking zone. Replacing a failed element restores proper heating response and consistent performance on that burner. What it does:

• Heats the 8-inch cooking zone by converting electrical energy to radiant heat beneath the glass
• Helps provide even heating and smooth simmer-to-boil control
• Works with the surface control to cycle and maintain the set temperature
• Typical failure symptoms: no heat, very slow heating, or inconsistent/uneven heating on that burner

• 1 Haliant 8-inch radiant surface element

• Disconnect power at the breaker; allow the cooktop to cool fully
• Lift/remove the glass top per your model's procedure to access the element
• Note wire locations and transfer any mounting clips/brackets from the old element if needed
• After reassembly, test the burner; if it still won't heat, the surface element switch/control may be at fault

Bottom-mounted bake element that provides the primary heat for baking. Replace when burned out or damaged to restore proper preheat and even baking.

• Supplies radiant heat from the bottom of the oven during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common failure signs: no heat in bake, slow preheat, uneven results, or visible cracks/blistering on the element
• A shorted element may trip the household circuit breaker when Bake is selected

• Disconnect power at the breaker or unplug; allow the oven to cool completely
• Remove racks; take out the element's mounting screws, gently pull it forward, and move the two wires to the new element one at a time using insulated pliers
• Don't let wires slip back through the rear panel; inspect terminals for heat damage, reassemble, restore power, and test preheat

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

1200w. Size: 6 inch. Location: Left front, right rear, and left rear.