Wall Oven Heating Element

This bake element restores even, reliable heat in the lower oven during the bake cycle. Replace it if the oven won't heat, struggles to reach temperature, or the element shows visible damage.

• Provides the primary heat source for baking in the lower oven cavity
• Common symptoms: no heat in bake, slow preheat, not reaching set temperature, uneven baking, or visible blistering/burn spots on the element
• Converts electrical energy to radiant heat for consistent oven performance

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove oven racks; take out element mounting screws and gently pull the element forward
• Support and transfer wires one at a time to the new element; ensure tight, secure connections
• Reinstall, restore power, and test for proper preheat and even heating

Fix uneven baking and undercooked centers by replacing your failed lower bake element. Restores consistent bottom heat for proper oven performance.

Oven won't heat or bakes unevenly? This lower bake element restores consistent heating and proper preheating. Moderately easy DIY repair.

Broiler not heating or browning evenly? This broil element restores intense overhead heat for proper broiling. Easy DIY replacement with basic tools.

Oven won't heat or takes too long to preheat? This lower bake element restores consistent heat during the bake cycle. Common DIY fix for cold ovens.

Oven won't heat or bakes unevenly? This lower bake element restores proper heating for baking and roasting. Easy DIY repair—unplug, swap out, done.

The Surface Element is an OEM part for Bosch cooktop and ranges. Measuring 6 inches across, it provides focused heat from below for smaller sized cookware.

Causes of a bad 6" plug-in element generally relate to normal wear and tear over time. Spills left on the coils could potentially cause issues by corroding internal wiring or damaging heating components.

Symptoms of a bad narrow surface element can include:

• The element heating intermittently or not at all
• Only parts of the coil visibly heating up
• Buzzing or clicking coming from below the element
• Tripped circuit breakers affecting that specific element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Broil element not heating? This upper heating element restores high-heat broiling and even browning. Straightforward DIY fix takes under 30 minutes.

Burner not heating or heating unevenly? This 6-inch surface coil element restores consistent heat to your electric range. Simple plug-in replacement.

Oven not browning food or broiling properly? This upper broil element restores direct high-heat cooking. Moderate DIY repair in 30-45 minutes.

Burner won't heat or stuck on high? This surface element restores proper heating control to your electric range stovetop. Common DIY repair.

This 20-inch bake element heats the bottom of the oven cavity so food cooks and browns evenly. Replacing a failed element restores proper oven heating and baking performance. What it does

• Heats the oven's bake chamber during bake cycles
• Replaces a cracked, burned-through, or non-heating bake element
• Helps resolve symptoms like no heat from the bottom, uneven baking, or oven failing to reach set temperature
• Works with the oven's control and safety circuits to provide consistent heat

• Disconnect power to the appliance at the breaker or unplug before starting
• Access usually requires removing the oven cavity bottom or back panel
• Handle the element by its insulated areas and avoid bending or touching the bare heating surface
• Tighten terminal connections securely and verify operation with the oven empty after reassembly

The Surface Element (240V-2100W) is an OEM part for Bosch cooktops and ranges. It provides consistent, even heating from below pans on the cooktop surface.

Causes of a bad surface element can include normal wear and damage from extended, heavy usage. Food or liquid spills left on the element for prolonged periods could potentially corrode the coils or electronics over time as well.

Symptoms of a bad surface element include:

• Element not heating up at all or heating unevenly
• Element heating intermittently or stopping prematurely
• Buzzing, clicking or smoke coming from below the element
• Tripped or blown circuit breakers when using that element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

If your cooktop burner won't heat or stays on high, this surface heating element may need replacement. Moderate DIY repair with basic tools.

This bake element heats the oven's lower chamber so food and bake cycles reach cooking temperatures. Replace a damaged or non-heating element to restore even baking and proper oven operation. What it does

• Converts electrical power into heat for the oven's bake cycle.
• Heats the oven's lower cavity to maintain set cooking temperatures.
• Commonly replaced for symptoms like no heat, weak heat, or uneven baking.
• Works with the oven's controls and sensors to deliver consistent bake performance.

• Disconnect power to the range at the breaker before starting any work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Remove the oven racks and detach mounting screws and wire connectors to replace the element.
• Only reconnect power after the element is secured and wiring is reattached; test on a short bake cycle.