Parts for Ge EWA2500A0WW: Washer Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

White. Left hand side

White. Right had side

Fix washer overflowing or underfilling issues with this water level pressure switch. Senses tub fill and prevents overflow. 15-minute DIY repair.

Mounting screw for refrigerators, dryers, and washers. Replaces lost, stripped, or corroded screws during repairs or part installations.

Replace your washer's control panel button if it's cracked, broken, or missing. This snap-in component installs on the control panel face plate.

Control knob and clip assembly for dryer or washer. Attaches to control shaft to set cycles and settings. Replace if cracked, broken, or missing.

The Knob Clip is an OEM part for GE washing machines and dryers. This small but crucial component is designed to secure the control knob to the appliance's control panel.  

Over time, knob clips can wear out or break due to frequent use or accidental damage. When this happens, the control knob may become loose, fall off easily, or fail to engage the control panel properly, making it difficult to set the appliance to the desired cycle or function.

Symptoms of a bad Knob Clip include:

• The control knob is loose or falls off the panel easily.
• Difficulty in adjusting settings due to a loose knob.
• The knob does not stay in place or slips when turned.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Size: 8-18 b.

Size: 8-18 b.

Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.

Plastic bushing that fits inside your washer's lid hinge for smooth pivoting. Replace if worn, cracked, or causing lid misalignment and squeaking.

Double-style bushing supports the washer lid hinge pin. Replace worn or cracked bushings to restore smooth, quiet lid operation and proper alignment.

Replaces a short wireform hinge that secures your washer lid or access panel. Order a new hinge if yours is rusted, bent, cracked, or missing.

A single replacement screw used to secure appliance panels, trim, and internal brackets so components stay aligned and reduce rattling. Simple, direct-fit fastener for restoring proper mounting and stable operation. What it does:

• Secures panels, mounting brackets, trim pieces and other appliance components
• Helps stop rattling, vibration, or loose panels caused by missing or stripped fasteners
• Restores proper alignment of doors and access panels when original screw is lost or damaged
• Matches the OEM fastening point for a straightforward hardware replacement

• Disconnect power to the appliance before working on electrical components or access panels
• Use the correct screwdriver to avoid stripping the head; match drive type to the screw
• Tighten firmly but do not overtighten—stop when snug to avoid damaging threads or parts
• Keep removed fasteners organized and compare with the replacement to ensure correct fit

Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.

Fix a washer that won't agitate or has broken fins. This agitator assembly snaps in place in under 5 minutes. Simple DIY repair, no tools required.

The Washer Agitator Coupler Kit is an OEM part for GE washing machines. This kit includes the coupler component that connects the agitator to the washing machine's transmission. It plays a pivotal role in the washing process by transmitting rotational force from the motor to the agitator, enabling it to move back and forth and effectively clean clothes.

Symptoms of a bad Washer Agitator Coupler include:

• The agitator failing to move or moving weakly during cycles, which can result in poorly washed clothes.
• Unusual noises from the washing machine during operation, indicating a mechanical issue.
• The agitator slipping or feeling loose when manually pushed or pulled.

Causes of a bad agitator coupler can include wear and tear from regular use, excessive load sizes that strain the agitator, or material fatigue that weakens the coupler over time.

This OEM replacement part is essential for restoring proper functionality to your GE washing machine and is also compatible with Hotpoint, RCA, and some Kenmore models.

Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.

The Drain Hose is an OEM part for GE washing machines. It is specifically designed to channel used water out of the washer and into the household drainage system. 

Causes of a bad drain hose can include physical damage from movement or installation, clogging from lint and debris, or degradation of the hose material over time, leading to leaks and inefficiency.

Symptoms of a bad Drain Hose include:

• Water leaking from the back or underside of the washing machine
• Pools of water around the area where the washing machine is installed
• Signs of wear or damage to the hose, such as cracks, holes, or bulging

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures washer tub and hoses to prevent leaks and noise. Replace if worn or broken to maintain proper alignment and seal. Verify fit with your model.

5/16-18 tpt ihw s n

The Washer Agitator Coupler Kit is an OEM part for GE washing machines. This kit includes the coupler component that connects the agitator to the washing machine's transmission. It plays a pivotal role in the washing process by transmitting rotational force from the motor to the agitator, enabling it to move back and forth and effectively clean clothes.

Symptoms of a bad Washer Agitator Coupler include:

• The agitator failing to move or moving weakly during cycles, which can result in poorly washed clothes.
• Unusual noises from the washing machine during operation, indicating a mechanical issue.
• The agitator slipping or feeling loose when manually pushed or pulled.

Causes of a bad agitator coupler can include wear and tear from regular use, excessive load sizes that strain the agitator, or material fatigue that weakens the coupler over time.

This OEM replacement part is essential for restoring proper functionality to your GE washing machine and is also compatible with Hotpoint, RCA, and some Kenmore models.

This Tub Seal is an OEM replacement part for GE washing machines that is responsible for preventing water from leaking from the tub. This part is located at the base of the washing machine tub and creates a seal between the tub and the transmission to prevent water from leaking out during the wash cycle. 

This part fixes the following symptoms-

• Water leaking from the underside of the washing machine.
• A musty or mildew smell coming from the machine.
• Unusual noises during use. 

Causes of a bad tub seal can range from normal wear and tear to a misaligned tub or an overloaded washing machine, which puts extra pressure on the seal. Additionally, the buildup of hard water minerals can degrade the seal's material over time.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This tub-bearing split ring is an OEM replacement part designed for GE washing machines. This part measures 2 inches in diameter. It is positioned between the inner and outer tubs to hold the tub bearing inside the outer tub. The Tub Bearing Split Ring not only supports the tub/hub assembly but also ensures smooth operation. 

Symptoms of a bad Tub Bearing Split Ring include:

• Excessive vibration or tub imbalance during spins  
• Loud clunking, knocking or grinding sounds  
• Reduced spin speeds or inability to achieve high RPMs
• Premature tub or bearing wear requiring replacement

Causes can be extended use over time which leads to wear and fatigue of the split ring material. Cracks or breaks can develop, reducing its stability and load-bearing capacity.

This genuine GE replacement part is also compatible with Hotpoint, RCA and some Kenmore front-load models. 

NOTE: For the washer outer tub seal order WH02X10383.

Replacement tub bearing for top-load washers. Fixes grinding, roaring, or loud humming noises during spin cycles. Verify fit with your model number.

Hub washer fits between the transmission and inner tub in top-load washers. Replace if cracked, worn, or causing leaks during operation.

Replaces a cracked or leaking wash tub to restore water containment and drum support. Fixes leaks, rubbing noises, and vibration. Confirm fit by model.

Baffle screw with flat washer for washers. Secures baffle or trim pieces to the washer body. Replace if screw is stripped, washer is missing, or worn.

Secures the inner tub to the outer tub in top-load washers. Replace if hub is cracked, broken, or rusted out to restore proper drum alignment and stability.

The Hub Nut is an OEM part for GE washing machines. This component secures the inner tub to the drive mechanism, ensuring that it remains in place during the agitation and spinning cycles. This lock-down nut is reverse threaded, meaning that it is loosed by rotating it clockwise. For easier removal of the old nut, it is recommended to use the tub nut spanner wrench WX5X1325.

Symptoms of a bad Hub Nut include:

• Unusual noises like banging or grinding during the spin cycle.
• The inner tub moving excessively or becoming loose.
• Leakage around the center of the machine, indicating a seal failure possibly related to a loose hub nut.
• Inefficiency in spinning or agitating clothes properly.

Causes of a bad hub nut can include corrosion due to exposure to water and detergent, improper initial installation, or loosening over time from the vibration and movement of the washing machine.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Outer tub cover kit for washers. Includes bleach funnel, clamps, wire tie, and cap. Replace if cracked, broken, or missing components after repair work.

Outer tub cover that snaps over the washer's outer tub assembly. Replace if cracked, broken, or missing to restore proper clearance and protection.

Size: 14-10 a trt 7/8 s.

Size: 8 - 18 ab.

Holds tub dampening straps in place on your washer. Replace if cracked, broken, or worn from heavy loads. Includes installation video guide.

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

This washer front panel assembly replaces a cracked, worn, or damaged console face. Restores appearance and provides housing for control buttons.

This washer front panel assembly replaces a cracked, worn, or damaged console face. Restores appearance and provides housing for control buttons.

This shipping bar assembly secures the oven door and internal components during transport to prevent movement and damage. Replacing a damaged or missing shipping bar helps ensure the range or oven door stays protected while moving the appliance. What it does:

• Holds the oven door and internal parts in place during shipment to reduce jostling and impact
• Prevents door misalignment or damage caused by transit
• Helps avoid rattling or loose parts after relocation
• Used only for transport/protection; remove before regular appliance operation if instructed by manufacturer

• One shipping bar assembly

• Intended for use during shipping/transport — confirm removal instructions in your owner's manual before operating the appliance
• Install or remove with the appliance powered off and according to manufacturer guidance
• Keep small fasteners and clips secure; replace any missing hardware with OEM-specified parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.

Grounding clip for top-load washers ensures proper electrical grounding. Replace if damaged, corroded, or missing to maintain safe operation. Verify fit with your washer model number before ordering.

Grounding stud for top-load washers. Connects electrical ground wire to washer frame. Replace if stripped, corroded, or missing for proper grounding.

Alignment pin keeps washer door hinge positioned so the door closes evenly. Replace if cracked, bent, or missing to restore proper door fit and seal.

Hex washer head screw for washer pedestals. Secures pedestal components and panels. Replace if screw is stripped, missing, or damaged during assembly.

Snap-in plastic clip cover that conceals fasteners and secures panels on your top-load washer. Replace if broken or missing to restore appearance.

Replaces worn or damaged washer sound dampening isolator. Reduces vibration and noise during wash cycles. Essential when original is cracked or missing.

The Lid Assembly is an OEM part for GE washing machines. This part is the lid of the washer. It is essential for securely covering the washer drum, preventing water from splashing out during the wash cycle, and allowing safe operation by ensuring the washer does not run with the lid open.

Causes of a bad lid assembly can include general wear and tear, physical damage from heavy loads or impacts, or issues with the hinges or latch mechanisms.

Symptoms of a bad lid assembly include:

• Difficulty in opening or closing the lid
• Washer not starting or stopping mid-cycle due to a faulty lid switch
• Visible cracks or damage on the lid
• Water leaking from the top of the washer

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Protects the washer's inner drum edge and prevents clothing from snagging on the tub lip. Replace if cracked, broken, or missing to avoid fabric damage.

Protects the washer's inner drum edge and prevents clothing from snagging on the tub lip. Replace if cracked, broken, or missing to avoid fabric damage.

Size: 1/4 - 20 b.

Secures the drive pulley to the transmission shaft in top-load washers. Replace if the original nut is backing off, stripped, or missing.

Supports the washer tub and absorbs vibration during cycles. Replace if corroded, worn, or broken to prevent drum sagging and banging during operation.

Suspension rod and spring assembly supports the washer tub and reduces vibrations. Replace if cracked, worn, or broken to restore proper tub support.

Size: 10-12 a. Includes 12 screws.

Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.

Base assembly for washers. Installs at the bottom of the cabinet to support the machine. Replace if cracked, damaged, or structurally compromised.

Adjustable leveling leg threads into washer base to stabilize cabinet and reduce vibration. Replace if cracked, broken, or missing for proper support.

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

Harness to corset & shifter

Replace your washer drive belt if the drum won't spin or agitate. Connects motor to drum for proper washing cycles. Confirm fit with your model number.

For retaining clip separately use WH1X2733. For washers with removable front panel.

Fix a washer that won't spin or agitates weakly with this motor and clutch kit. Solves pulsing motors and failed spin cycles. DIY repair takes 2-3 hours.

Replace your washer's housing cover if the original is cracked, broken, or missing. This protective cover installs on the exterior to shield internal components.

These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.

This part fixes the following symptoms:

• Loose or wobbly parts or panels within the appliance's interior or exterior
• Panels or components falling out of place, creating gaps or exposing internal parts
• Unusual noises or rattling sounds during the appliance's operation

The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.

If your washer won't fill, overfills, or leaks when off, the water inlet valve may be faulty. Simple 10-20 minute DIY repair with basic tools.

12-pack of inlet hose washers for washers and washer dryer combos. Replace cracked, worn, or missing washers to prevent leaks at water connections.

Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.

Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.

The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.

Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.

Symptoms of a bad drain hose clip include:

• Water leaking from the back of the washer
• Drain hose detaching or becoming loose during operation
• Difficulty securing the drain hose in place
• Visible damage or cracking on the clip

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For the entire drain hose, use part number WH41X10096.

Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.

Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.