Need Help?
Call
Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.
Controls airflow between freezer and fresh food compartments. Attaches to the damper control shaft. Replace when cracked, stripped, or missing.
Just ordered the part and the filter, I was very happy because I ordered the parts in one day and was delivered on the next day. Read more
Gas smell during or after cycles? Dryer won't heat? Replace the gas valve assembly to restore proper gas flow and safe operation. Advanced repair.
Frigidaire Gallery gas dryer from maybe 15 years ago. Based on the fact the the smell was only in the dryer, I concluded it must be the gas valve failing to completely seal when closed. After looking at the insides again, I suppose it is possible that it was a connection near the burner, but that stuff had remained untouched for 10 years so I still think I made a good assumption. I got a new ignitor as well since I was in there, and compared to the valve, it was cheap! I thought I could get in... Read more
Fix a refrigerator that won't cool, runs constantly, or freezes food with a new temperature control thermostat. Regulates compressor cycling.
Replaced thermostat Read more
Burners won't light or no clicking sound? This spark module sends high-voltage pulses to ignite surface burners. DIY-friendly replacement fixes ignition.
Replace spark module. Read more
Seals front and rear tub halves to prevent water leaks. Replace if you notice leaking during wash cycles or after bearing repair. Verify fit with your model.
I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more
Ice won't dispense or jams in crushed mode? This crusher blade fixes bent or broken blades in your ice bucket assembly. Easy DIY repair with video guide.
I ordered (3) new replacement blades and received them in two days! Read more
Replacement shelf support bracket for freezers. Secures and stabilizes freezer shelves. Replace if broken, cracked, or missing due to heavy loads or age.
Bought two clips and bar, the bar was bent and I replaced both clips. Worked great. Read more
The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.
The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.
Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.
Symptoms of needing Touch Up Paint include:
Quick touch up. The paint worked great. Packaged with a brush like nail poliish Read more
This kit includes the start relay and overload protector that help the compressor motor start and run properly. The relay provides the initial electrical boost to get the compressor running, while the overload protector shuts it off if it draws too much current or overheats. Replace this kit if the refrigerator or freezer is not cooling, the compressor clicks on and off repeatedly, or you hear a buzzing sound coming from the back of the unit.
Looked for obvious signs of mal-function, burned wires, etc. I found that the compressor controller(attached to the compressor) had an obvious burned-out spot. Took a chance that was the problem (it was); ordered all new OEM parts, including a new timer and run capacitor (a part that kicks in every time the compressor starts). I received the parts at 1 PM EST; by 1:48 PM I had the freezer working. Easily saved $250.00. A nice aside was that an Internet competitor was asking $53.00 for the same... Read more
Washer won't spin or agitate? Humming motor or clothes staying wet often means a failed drive motor. This repair typically takes 15-60 minutes with basic tools.
I took the easy fix first and replaced the Capacitor. That got me three loads before the motor burned out. I ordered the motor from AppliancePartsPros.com after a google search for "best price model # 134159500 Drive motor " The part arrived in 5 days, and it took about 15 minutes to remove the old motor and replace it with the new one. Simple and easy. four screws, four nuts, and two electrical connections. — The hardest step was one of the four mounting screws was way back inside and it took... Read more
Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.
Husband installed the glass and trim it looks great! Read more
Ice dispenser not working but ice is in the bin? The auger motor rotates the auger to feed ice through the chute. DIY-friendly repair in under an hour.
Replaced motor and new solenoid and yoke assembly, motor ran fine but Ice maker did not make Ice, water was turned on and the wire off and on latch was is the down position (on). Disconnected the water line from the Ice maker tray, ice had formed in the line while I was waiting for my parts (about 5 days), I would suggest disconnecting the water line at the feed end were your shut off valve is located and allow water to drain out of line. I had to remove Ice tray and submerge it pan of hot... Read more
Glass insert that sits in the crisper cover frame above your produce drawers. Replace this part if your original is cracked, broken, or missing.
Replaced the glass cover. Read more
Fix water or ice dispenser not working with this 4-button control switch assembly. Common fix when buttons fail to respond or dispense incorrectly.
Replaced the four-button switch assembly. Read more
Color: white. It measures about 3 inches in diameter.
Replaced the broken knob with a new one. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.