Whirlpool Dishwasher Parts

This pump and motor assembly replaces the dishwasher's pump to restore proper water circulation and draining. It helps clear standing water and maintain wash performance when the original unit is worn or leaking. What it does:

• Drives water flow for normal wash cycles and pumps wastewater out during drain
• Restores proper draining when the dishwasher leaves water in the tub
• Reduces or eliminates grinding, humming, or squealing noises caused by a failing pump motor
• Helps resolve common drain-related error codes and poor wash results tied to low circulation

• One pump and motor assembly

• Disconnect power and water supply before beginning any repair
• Expect residual water in the tub and hoses; have towels or a pan ready
• Handle electrical connectors and hoses gently; replace any damaged clamps or seals
• Test the dishwasher on a short cycle after installation to ensure proper drain and flow

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This genuine OEM adjuster helps set and fine-tune an appliance's alignment so doors close correctly and the cabinet sits level. It restores stable operation and reduces rocking or vibration caused by an uneven appliance surface. What it does:

• Provides a threaded adjustment point to raise, lower, or support an appliance corner or panel
• Helps correct uneven cabinets, tilted doors, or appliances that rock or vibrate during use
• Restores proper door alignment and sealing when misalignment is caused by height/level issues
• Works as the appliance's mechanical support where an adjustable foot or bracket is used

• Always disconnect power (and water, if applicable) before servicing the appliance
• Support the appliance securely before making height adjustments or removing/installing the adjuster
• Use appropriate hand tools; avoid excessive force that could damage threads or mounting points

This Leveler is the adjustable foot that supports and levels your appliance. Replacing a worn, cracked, or missing leg helps stop rocking and vibration, improving stability and ensuring smooth, quiet operation.

• Screws into the base to set height and keep the appliance level and secure
• Helps reduce rocking, vibration, and rattling that can cause excess noise
• Supports proper alignment and smooth door/closure operation when level
• Common symptoms: appliance wobbles, leg is stripped or broken, difficult to keep unit level

• Disconnect power and shut off gas/water if applicable before servicing
• With help, tip or lift the appliance slightly and protect the floor
• Thread the new leveler into the mounting boss and adjust height with a level
• Verify the unit is stable by gently rocking and recheck level after initial use

The Door Handle is an OEM part specifically designed for Whirlpool dishwashers. It controls access for loading and unloading dishes. 

Causes of a faulty handle could include worn plastic materials susceptible to cracking after years of use. Lever mechanisms sustain stress with each movement.

Symptoms of a bad door handle include:

• Failure to properly open or close the dishwasher door
• Loose, dangling, or detached handle operation  
• Fastener deterioration compromising secure fit 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models as well.

This is the rear wheel support for a dishwasher rack. It helps guide and support the rack as it slides in and out, restoring smooth movement and preventing the rack from binding or derailing.

• Supports and guides the rack at the rear during opening/closing
• Helps correct issues like a wobbly, sticking, or misaligned rack
• Can address noisy, rough rack travel caused by a worn support
• Maintains proper rack tracking to reduce derailment

• Disconnect power and water before servicing
• Pull rack forward to access the rear support area
• Depress locking tabs/retainer to remove the old support; press-fit the new support until secure
• Verify smooth rack travel before returning the appliance to service

This black timer knob replaces a worn, cracked, or missing control knob so you can easily set the oven or range timer. Restores a positive grip and clear pointer for accurate timer adjustments. What it does:

• Fits onto the timer/control shaft to allow manual setting of the cook/timer function
• Replaces broken or stripped knobs that spin or won't engage the control
• Provides a visible pointer for precise timing and repeatable settings
• Improves user grip and control when turning the timer dial

• One black timer knob

• Power off the appliance before servicing electrical controls
• Pull the old knob straight off the shaft; align and push the new knob onto the splined shaft until fully seated
• Do not force the knob onto the shaft; verify correct spline alignment to avoid damage
• If the knob does not seat or the control shaft is damaged, inspect the control assembly and replace as needed

This is a genuine replacement screw used to secure components and panels on compatible Whirlpool appliances, restoring a firm, vibration-free fit. It replaces worn or missing fasteners to help keep parts aligned and stable. What it does

• Secures panels, brackets, or internal components to prevent shifting or rattling
• Replaces stripped, rusted, or missing screws that cause loose parts or noise
• Helps maintain proper alignment of mounted components for safe operation
• Useful when reassembling repair work or after removing parts for service

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power before servicing electrical appliances; follow OEM safety guidance
• If screw threads or holes are damaged, replace both screw and mating hardware as needed

This motor-pump assembly replaces the washer's drain pump to restore reliable water removal and reduce leaks. It mounts to the tub and handles draining so your cycle can finish and clothes can spin out properly. What it does:

• Pumps water out of the washer during drain cycles to allow proper spin and cycle completion
• Helps prevent standing water and reduces the chance of overflow or tub leaks
• Stops humming, grinding, or no-drain symptoms caused by a failed pump motor
• Works as the integrated motor and pump unit that attaches to the washer tub

• Disconnect power and water before servicing; follow all safety precautions
• Basic hand tools required; access may require removing front or rear service panel
• Inspect and reinstall hoses and clamps securely to prevent leaks

This positioner aligns and secures its mating component in the correct location inside your appliance. Replacing a cracked, worn, or missing positioner restores proper fit so the assembly stays put and operates as designed.

• Holds the related part in the proper position and orientation
• Prevents shifting, sagging, or rattling during use
• Supports smooth adjustment or movement where applicable
• Common symptoms: loose or misaligned component, difficulty adjusting or seating the piece, visible cracks, or a missing clip

• Disconnect power; also shut off gas or water if your appliance uses these utilities
• Note the original orientation and take photos before removal
• Transfer any reused hardware and fully seat tabs/slots to avoid damage
• Wear cut-resistant gloves and check alignment after reassembly

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

This silverware basket is a dishwasher utensil caddy that organizes forks, knives and spoons so cutlery cleans evenly and stays contained during the wash cycle. It fits into the lower rack and helps prevent items from shifting. What it does:

• Holds and separates silverware and small utensils for better cleaning and safer handling
• Keeps loose items from falling into the wash area or blocking the spray arms
• Snaps into the lower dishwasher rack to stay secure during cycles
• Works with standard dishwasher racks that accept a removable utensil caddy

• One silverware basket

• Place the basket into the lower rack and align so it sits securely in the rack slots
• No tools required for standard installation; handle with care to avoid sharp utensils
• Inspect for broken tabs or clips before installing; damaged mounting points can allow the basket to shift
• Clean periodically to remove food buildup and prevent odors

This roller fits the cable bracket assembly and helps guide the cable smoothly to reduce binding and wear. It restores proper cable tracking so the mechanism moves more quietly and reliably. What it does:

• Guides and supports the cable within the bracket so the cable runs true
• Reduces rubbing, binding, and premature cable wear
• Helps eliminate squeaks or grinding where the cable contacts the bracket
• Restores smoother operation of the affected door/assembly movement

• One roller for the cable bracket (quantity: 1)

• Disconnect power before starting any repair and follow all safety guidelines
• Requires basic hand tools; access the bracket per your model's service instructions
• Inspect the cable and bracket for wear or damage and replace if necessary
• Test operation after installation to ensure proper cable routing and smooth movement

Color: White. Size: 13 oz. Spray paint primer. can.

This spring kit replaces worn or broken return springs in the applicable assembly, restoring proper tension and smooth movement so the mechanism operates reliably throughout the cycle and returns to its proper position. What it does:

• Provides the correct tension to move or hold parts in place
• Helps resolve weak return action, sticking, failure to engage/latch, or sagging components
• Can reduce noise caused by loose or fatigued springs
• Maintains consistent operation throughout the appliance's cycle

• Manufacturer-supplied spring kit

• Disconnect power; turn off water supply if applicable
• Springs are under tension—use eye protection and release carefully
• Note original spring routing and attachment points before removal
• Replace both for balanced operation