Whirlpool Dryer Parts

This is a flexible seal that fits around the dryer door or door window to prevent heated air and moisture from escaping the drum area. It creates an airtight barrier between the door and the front panel of the dryer. Replace this seal if your dryer is leaking warm air around the door, taking longer than normal to dry clothes, or if the seal is cracked, torn, or visibly worn.

Left hand hinge. For right hinge use WP8066056

Replace your worn dryer door seal to restore a tight closure, contain heat and moisture, and eliminate rattling or squeaking. Easy snap-in install.

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

Dryer won't advance through cycles or keeps running after finishing? This timer controls cycle sequencing and shutoff. Typical DIY repair in 15 minutes.

Adjustable leveling leg threads into the dryer base to set height and stabilize the unit. Replace worn, missing, or damaged legs to eliminate rocking.

Fix a dryer door that won't stay closed with this door catch bezel. Secures the latch mechanism for proper door closure during operation.

This drive motor powers the appliance's main drive system, converting electrical energy into steady rotation under load. Replacing a weak, noisy, or seized motor restores proper movement and dependable operation. What it does

• Provides the mechanical torque that turns the appliance's drive system
• Resolves symptoms like no movement, humming/buzzing without turning, or stalling under load
• Helps eliminate intermittent starting and overheating shutdowns
• Reduces grinding/squealing motor noises caused by worn bearings or a failing armature

• One drive motor assembly

• Disconnect power before servicing; also shut off gas supply
• Take photos/label wires, then transfer connectors and any mounting parts from the old motor
• Ensure the motor spins freely and the belt/pulley alignment is correct before reassembly
• After installation, perform a brief test run while observing for smooth, quiet operation

Transfers motor rotation to spin the dryer drum. Replace if you hear squealing, the drum won't turn, or clothes aren't drying. Verify fit by model number.

Supports the front drum edge for smooth, quiet rotation. Replace when worn to stop scraping noises or drum wobble. Confirm fit with your model number.

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may compromise the handle's structural integrity and make it less reliable.

Color: White

Symptoms of a bad Dryer Door Handle include:

• Loose or wobbly handle
• Cracks or visible damage to the handle
• Difficulty opening or closing the dryer door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replace your broken, cracked, or missing range surface burner control knob. Installs on the control valve stem to adjust heat levels on cooktops.

Right-hand door hinge for dryers. Replaces broken, bent, or sprung hinges that prevent the door from closing properly. Easy DIY installation.

4-wire power cord connects your electric dryer to a 4-prong household outlet. Replace a worn, damaged, or overheated cord to restore safe power connection.

If your dryer makes loud ticking or grinding noises, a cracked or broken blower wheel is often the cause. This replacement wheel restores airflow.

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing