Whirlpool Dryer Parts

The Coin Box is an OEM replacement part for Whirlpool combo washer/dryers. It provides a storage space for coins used to operate the unit. The coin box slots ensure collected change remains safe and secures payments for laundry cycles.

Causes of a bad coin box can be normal wear from hundreds of deposits, minerals clogging slots, or physical damage compromising security.

Symptoms of a bad coin box include:

• Coins not being accepted or properly collected
• Box distorting shape or developing cracks over time
• Change falling out or going missing

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The door switch detects whether the dryer door is open or closed, enabling the motor and heater only when it's safe. Replacing a failed switch restores proper start/stop control and drum light behavior.

• Senses door position and completes or interrupts the dryer's run/heat circuits
• Shuts the dryer off when the door opens for safety
• Common symptoms: dryer won't start with the door closed; doesn't stop when door opens; drum light stays on or won't turn on
• Intermittent operation when the door is moved or pressed

• Disconnect power before servicing; allow components to cool
• Access the switch from the door opening or front panel; remove screws or release locking tabs
• Note wire positions and transfer them one at a time to the new switch
• Verify operation before reassembly: dryer should not run with the door open; drum light should respond

This thermal limiter (89°C) is a one-time, temperature-sensitive safety device that opens the circuit if internal temperatures rise too high. Replacing a failed limiter helps protect the appliance from overheating and can restore normal operation. What it does:

• Monitors temperature in the airflow/heating path and opens around 89°C to interrupt power when overheating occurs
• Helps protect wiring, controls, and heater components from thermal damage
• A blown/open limiter can cause: appliance won't start, no heat, or stops mid-cycle
• Often indicates an underlying overheating issue that should be corrected

• 1 thermal limiter

• Disconnect power (and gas supply if applicable) and allow the unit to cool before servicing
• Access the limiter per the service information; note wire positions and transfer leads one at a time
• Replace only with the correct rated limiter; never bypass this safety device
• After installation, clear airflow restrictions and verify proper venting and heater/thermostat operation

This broken belt switch is a dryer safety switch that senses drive belt tension and opens the motor circuit if the belt breaks or slips off. Replacing a failed switch can resolve a no-start or no-tumble condition. What it does:

• Monitors drive belt tension via the idler assembly
• Interrupts power to the motor when the belt is broken or not tensioned
• Helps prevent heating without airflow when the belt has failed
• Symptoms can include: dryer won't start, drum won't turn, or the dryer stops as soon as the Start button is released

• 1 switch

• Disconnect power; for gas models, shut off the gas supply
• Access the switch near the idler pulley by removing the lower/front panel per your model
• Transfer wires from the old switch to the new one; mount securely with the actuator aligned to the idler arm
• Run a brief test cycle

This sensor monitors humidity inside the microwave cavity so sensor-cook and reheat features can automatically adjust time and power. Replacing a failing sensor restores accurate automatic cooking and helps prevent premature shutdowns or "Sensor" error messages.

• Detects steam/humidity in the cavity during sensor-based cooking cycles
• Sends feedback to the control to optimize cook time and power levels
• Failure can cause "Sensor" errors, sensor-cook cycles that won't start or end early
• Manual timed cooking may still work while sensor-cook modes misbehave

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that can retain a dangerous charge
• Access is typically behind the top grille/control area; note sensor orientation before removal
• Handle the sensor by its body; avoid contaminating the sensing face
• Route wiring as original and ensure the connector is fully seated before reassembly

This power relay is an electromechanical switch with a 48 VDC coil that lets the control board safely turn high-voltage components on and off. Replacing a weak or sticking relay helps restore consistent, reliable operation. What it does:

• Uses a 48 VDC coil signal from the control to open/close internal contacts
• Switches AC line power to high-demand loads (e.g., heater, motor, fan, or compressor)
• Helps maintain stable cycling and prevents intermittent operation
• Helps with symptoms such as no heat or no run, intermittent operation, clicking with no activation, or a component stuck on

• Power relay (48 VDC coil)

• Disconnect power to the appliance before servicing; allow capacitors to discharge
• Note/photograph wire locations and move wires one at a time to matching terminals
• Ensure terminals are fully seated; replace any burnt or loose connectors
• Mount in the original orientation and secure firmly to prevent vibration

This Dryer Drying Rack creates a stationary shelf inside the drum so items that shouldn't tumble—like shoes, sweaters, and hats—can dry gently. Replace a missing or damaged rack to restore safe, non-tumble drying capability.

• Provides a stable platform inside the dryer for items that need to stay still while drying
• Helps reduce wear, scuffing, and noise from tumbling delicate or bulky items
• Restores function when the original rack is cracked, warped, or missing
• Common symptoms: rack won't seat/lock, sits unevenly, or items won't stay on the rack

• Disconnect power before installing
• Open the door and seat the rack so the rear support engages the back ledge/slots and the front rests on the door opening
• Ensure the rack is secure and clear of the rotating drum; load items evenly
• Remove the rack before returning to normal tumble cycles

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This mechanical defrost timer automatically switches the refrigerator between cooling and defrost cycles. Replacing a failing timer helps clear evaporator frost so temperatures remain stable and cooling performance is consistent. What it does:

• Initiates the defrost cycle at regular intervals and then returns the system to cooling
• Interrupts compressor power and energizes the defrost heater during defrost
• Helps prevent heavy frost buildup on the evaporator
• Common failure symptoms include thick frost on the evaporator/back wall, warming in the fresh food section, the unit running constantly or getting stuck in defrost, or repeated clicking from the control area

• 1 defrost timer

• Disconnect power before servicing; components in the defrost circuit can be live and hot
• Access locations vary by model
• Note or photograph wire positions; transfer wires one at a time to the new timer
• Secure the timer in the original bracket/orientation and reassemble before restoring power

This door catch assembly secures the door by engaging the mating latch or strike, keeping it firmly closed for proper operation and safety. Replace a worn or broken catch to restore reliable door closure and consistent performance. What it does

• Engages the door latch/strike to hold the door closed during use
• Helps maintain proper door alignment and contact with seals/interlocks
• Restores a positive latch feel and consistent closure
• Common signs of wear: door won't latch or pops open, must be slammed to close, visible damage to catch tabs

• One door catch assembly

• Unplug the appliance or switch off power at the breaker before servicing; for gas appliances, shut off the gas supply
• Open the door, access the catch at the cabinet/frame, and remove retaining screws or clips
• Transfer any reusable hardware from the original part and install the new catch
• Verify smooth latch engagement and door alignment before restoring power

This small wheel mounts to the dishwasher rack and lets it roll smoothly along the rails. Replacing a worn or broken wheel restores easy rack movement and helps prevent jams, derailments, and track damage. What it does:

• Provides rolling support so the rack glides in and out on the rails
• Helps keep the rack level and properly aligned
• Replace if the wheel is cracked, flattened, loose, or missing
• Common symptoms: rack binds or falls off track, wobbles, or makes scraping/grinding noises

• 1 wheel

• Disconnect power and water if working inside the tub; for rack-only service, remove the rack and work on a stable surface
• Remove end caps/stops and slide the rack out
• Release the old wheel from its clip/axle and install the new wheel securely
• Reinstall rack and end caps; verify smooth travel on both rails

This is a white replacement handle assembly that restores a solid, comfortable grip and fresh appearance to your appliance. Use it to replace a cracked, loose, or missing handle so doors or drawers open and close smoothly.

• Provides the rigid handhold used to open and close the appliance door or drawer
• Helps resolve a loose, broken, or missing handle
• Can improve operation when the door is hard to open due to a damaged handle
• Refreshes the look of the appliance after cosmetic wear or discoloration

• Disconnect power before servicing
• Open the door to access mounting fasteners; retain and reuse original screws and any trim caps
• Transfer any spacers or brackets from the old handle to the new one
• Align carefully and tighten fasteners evenly—do not overtighten

This gas surface burner head distributes fuel through its ports to create an even, reliable flame on your cooktop. Replace a clogged, damaged, or warped head to restore consistent ignition and proper heat on the affected burner.

• Channels gas through precision ports to produce a steady, even flame
• Interfaces with the surface igniter/electrode for quick, reliable ignition
• Replaces worn or clogged heads that cause weak, uneven, or yellow flames
• Helps resolve delayed ignition or a burner that won't light

• Disconnect electrical power and shut off gas supply before servicing
• Remove grate and burner cap, lift off the old head, and clean the mating surface
• Align the new head with the igniter and locating features; seat it fully before replacing the cap
• Restore gas and power; test ignition and verify proper flame pattern

Color: Chrome

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

This door seal restores a tight, even closure between the door and cabinet opening. Replacing a worn seal helps contain heat and moisture, prevent leaks or steam escape, and bring the appliance back to consistent performance.

• Forms a continuous gasket around the door perimeter for proper closure
• Helps prevent water, steam, or air from escaping during operation
• Supports correct temperature and cleaning/drying performance
• Replace if the seal is torn, flattened, brittle, or if you notice leaks, steam escaping, or longer preheat/cycle times

• Disconnect power; shut off water and allow the unit to cool completely
• Remove the old seal from its channel and clean the groove and mating surfaces
• Press the new seal evenly into the channel, ensuring corners seat fully without twists
• Close the door for several hours to help the gasket conform; check for uniform contact all around