Whirlpool Dryer Parts

Fix dryer underheating or overheating issues with this 140°F fixed thermostat. Restores accurate temperature control and stops erratic cycling. Easy repair.

Dryer won't start or door won't stay closed? A worn door strike prevents proper latching. Simple 10-minute fix with just a screwdriver. Video guide included.

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Flexible narrow brush reaches under and behind refrigerator cabinet to clean condenser coils and vents. Replace worn or missing brush to remove dust buildup.

Securely mounts your dryer above your washer to save floor space. Includes brackets, adhesive pads, and hardware for safe installation. Replaces lost kits.

LED light bulb for refrigerator and freezer compartments. Replace when lighting fails or dims. Verify fit by checking your model number compatibility.

Indicator light lens covers the pilot lamp opening on your range control panel. Replace when cracked, discolored, or missing to restore visibility.

Seals the dryer door perimeter to contain heat and prevent air leaks. Replace if damaged, stretched, or pulled off during cycles. Confirm fit with your model.

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Dryer won't heat or clothes stay wet? A failed heating element is often the cause. This part restores consistent heat to dry clothes properly again.

Dryer won't start or makes squealing noise? A faulty motor assembly stops operation or causes loud grinding sounds. Moderate DIY repair restores function.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Dryer won't start but lights work? A faulty door switch prevents operation. This replacement switch restores normal function in under 10 minutes.

This replacement timer knob attaches to the control panel timer so you can set and adjust time reliably. Replacing a worn or missing knob restores a secure grip and clear pointer orientation for everyday use.

• Attaches to the timer shaft to turn and set the kitchen timer
• Common fix for knobs that are cracked, stripped, loose, or missing
• Helps when the timer can't be set or the shaft spins without turning
• Restores smooth rotation and proper alignment on the control panel

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft
• Align the new knob with the shaft and press firmly until fully seated
• Test timer operation and pointer alignment before restoring power

This replacement door switch restores proper door sensing in your refrigerator. It detects when the fresh food or freezer door opens and closes, turning interior lights on/off and signaling the control so door-ajar alerts and related features work correctly. What it does:

• Senses door position to control interior lighting
• Sends door status to the control in many models for features like door-ajar alerts or fan pause
• Helps prevent overheating near the light by ensuring it turns off when the door is closed
• Common symptoms of failure: no interior light, light stays on, flickering light, or persistent door-ajar alarm

• 1 door switch

• Disconnect power to the refrigerator before servicing
• Carefully release the old switch from the cabinet opening and unplug the wire harness
• Connect the harness to the new switch, orient correctly, and snap or seat it fully in the opening
• Restore power and verify proper light operation and door-ajar indication