Whirlpool Dryer Parts

Replaced Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

• Marks left on clothes

After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify... Read more

Remove and replace Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

I tried to buy a new refigerator, but strangely none of the major stores had anything I wanted in stock. The earliest delivery date for a new unit was over a month away. At that I decided to try and keep this one running. I did online research into common refigerator problems. I found the cooling coils in the freezer were covered in a block of ice and frost. The refigerator was not going through a defrost cycle. With a hair dryer I thawed out the coils. The refigerator worked fine for... Read more

• Timer will not advance

I'm not at all an expert in repairs...I learn how to fix things as they break by researching online so that I don't have to pay a repairman and by doing so have learned a lot of things as a homeowner, but this was my first dryer repair. My dryer had been working perfectly and then suddenly wouldn't start. The inside light still functioned, so it was still getting power. There was a quiet ticking noise coming from the back when plugged in which I determined to be from the timer trying to... Read more

I looked on Appliancepartspros.com, it helped me diagnose the problem, told me what parts to buy and showed me a video of how to fix it. Therefore I saved $150 by not having to call a repair shop. Read more

Ordered new trap assemble and replaced broken trap. slight redesign but same fit Read more

Replaced blower belt and nut as per your You tube video. Read more

Replaced blower belt and nut as per your You tube video. Read more

I replace the old timer with the new one I purchased from appliance parts pros.com I removed the nuts from back of top console of the dryer. Removed the electrical prongs from the old timer and then replace with new timer than plug dryer in wall and started the dryer on timed cycle and the heating elements kicked in and my wife was smiling from ear to ear. Read more