Whirlpool Fuse Or Sensor

This thermostat temperature limiter helps stop heating when temperatures exceed safe levels, protecting the appliance and preventing overheating. It fits specific Whirlpool systems and restores proper temperature control when the limiter has failed. What it does

• Acts as a safety cutoff to interrupt heating when internal temperatures get too high.
• Prevents the appliance from continuing to heat during an over-temperature condition.
• Common symptom: appliance runs but produces little or no heat.
• Common symptom: heating cycles off prematurely or intermittently.

• One thermostat temperature limiter.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Handle and route wiring carefully; replace only with the exact OEM part number.
• Test circuits with a multimeter to confirm thermostat failure before replacing.

This thermostat temperature limiter helps regulate oven temperature and prevents overheating by signaling the control when set limits are reached. It replaces a faulty limiter to restore proper temperature control and safer operation. What it does

• Acts as a temperature-sensitive switch that opens or closes at a set temperature to limit heat.
• Prevents the oven from exceeding safe temperatures by cutting power to the heating circuit when triggered.
• Commonly used when the oven won't reach or maintain set temperatures, or when it overheats and shuts down.
• Works as a safety/limit device in the appliance's temperature control system.

• One thermostat temperature limiter

• Disconnect power at the breaker or unplug the appliance before servicing.
• Handle terminals carefully and secure wiring to original connections; avoid bending or stressing the sensor.

This temperature sensor monitors refrigerator temperature and sends readings to the control board so the appliance can regulate cooling. Replacing a failing sensor restores accurate temperature feedback for reliable cooling performance. What it does

• Measures internal temperature and reports it to the refrigerator control board
• Helps the system cycle the compressor and fans correctly for stable temperatures
• Commonly linked to symptoms like poor cooling, frequent compressor run, or temperature-related error codes
• Works as the sensing element for automatic defrost and temperature-control routines

• One temperature sensor (thermistor) with attached lead

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the sensor and wiring gently; secure the lead per factory routing to avoid contact with moving parts
• May require basic hand tools and access to the evaporator/thermostat area

This thermostat is a direct-replacement oven temperature control that helps the oven maintain the set cooking temperature for consistent bake and roast results. It restores proper temperature sensing when the original fails. What it does:

• Senses oven cavity temperature and signals the heating element or gas valve to cycle on/off
• Helps correct issues like oven running too hot, too cool, or baking unevenly
• Works as the temperature-regulating sensor used by the oven control system
• Matches OEM function for reliable temperature control and repeatable cooking results

• One thermostat as shown

• Disconnect power (or gas) before beginning any repair; verify power is off with a meter
• Accessible from the oven control housing or rear panel on most models; remove trims/panels as needed
• Handle component and capillary/tubing carefully to avoid kinks or damage

This RTD temperature sensor measures water and component temperature so the appliance can detect and control cycles more accurately. Replaces a failed or inconsistent temperature reading to restore proper cycle performance. What it does:

• Senses temperature using an RTD element and sends readings to the control board
• Helps the machine regulate water/air temperature for correct cycle operation
• Commonly replaces a sensor that reads open, out-of-range, or causes temperature-related cycle errors
• Supports accurate heating/cooling decisions that affect wash/dry performance

• Disconnect power before inspecting or replacing the sensor to avoid shock
• Handle the probe and wiring gently; avoid bending or crimping the sensing element
• Verify connector polarity and secure wiring to factory mating connector

This fixed thermostat monitors and limits temperature to protect the appliance's system and components. It's a simple, non-adjustable sensor/limit switch used where a set cutoff temperature is required for safe operation. What it does:

• Opens or cuts power when the monitored temperature reaches its fixed limit to prevent overheating
• Helps stop continuous heating cycles caused by a failed control or sensor
• Commonly used as a safety cutoff in temperature-control circuits
• Can resolve symptoms like persistent overheating, failure to stop heating, or temperature-related shutdowns

• One fixed thermostat (single unit)

• Disconnect power before inspecting or replacing the thermostat to avoid shock or damage
• Handle gently; avoid bending terminals or stressing sensing elements

This thermostat retainer secures the refrigerator thermostat or temperature sensor in place to ensure accurate temperature sensing and stable operation. It replaces a worn or broken mounting clip to restore proper sensor positioning. What it does:

• Holds the thermostat/temperature sensor firmly against the evaporator or designated mounting point
• Prevents sensor movement that can cause erratic temperature readings or cooling issues
• Maintains correct sensor alignment for reliable refrigerator temperature control
• Helps reduce vibration and wear on the thermostat assembly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access may require removing interior panels or trim; keep fasteners organized
• Handle the thermostat and sensor carefully to avoid damaging the sensing element or wiring

This thermistor is a refrigerator temperature sensor that monitors internal air temperature so the control board can regulate cooling. Replaces a failed sensor to help restore accurate temperature readings and more consistent cooling. What it does:

• Senses internal refrigerator temperature and sends a variable resistance signal to the control board
• Helps the control system cycle the compressor and fans correctly for stable temperatures
• Commonly replaced when refrigerator runs too cold, too warm, or has irregular cooling cycles
• Can address temperature-error codes or defrost control issues when the sensor is faulty

• Disconnect power to the appliance before inspecting or replacing the sensor
• Handle the sensor and wiring harness carefully to avoid damage to the probe or connectors
• Install in the original sensor mounting location and secure wiring away from moving parts

This thermostat is a temperature-limiting control that helps regulate oven/cooking temperature and prevents overheating for safer operation. It replaces a failed limiter to restore proper temperature control and reliable heat cycling. What it does

• Opens or interrupts power when oven temperature exceeds the set limit to prevent overheating
• Restores normal thermostat cycling when the original limiter fails or sticks
• Common symptom: oven runs too hot or will not maintain set temperature
• Common symptom: oven shuts off or will not heat because limiter has opened

• One thermostat (temperature limiter) as shown

• Disconnect power to the appliance before attempting any service
• Access location, removal, and wiring vary by model; refer to your model-specific service instructions
• Handle the sensing element carefully; do not kink or damage the capillary/tube

This thermostat is the temperature-sensing switch that helps the appliance maintain its set temperature for reliable operation. It replaces a failed temperature control that causes improper heating or cooling performance. What it does:

• Senses temperature and opens or closes the circuit to control heating/cooling cycles
• Prevents overheating by interrupting power when temperatures exceed set thresholds
• Restores normal cycling when the control no longer conducts (common with failed thermostats)
• Common symptoms include the appliance not reaching or holding temperature, cycling too frequently, or running continuously

• One thermostat

• Disconnect power before servicing to avoid shock or injury
• Follow the appliance service manual for removal and proper wiring location
• Verify electrical continuity of the old and new thermostat with a multimeter before and after installation

This high-limit thermostat is a temperature safety switch that helps prevent overheating by opening the circuit when temperatures exceed safe limits. It restores normal operation once the temperature cools, protecting the appliance and reducing fire risk. What it does:

• Monitors internal temperature and opens the circuit if heat gets too high
• Prevents overheating that can cause damage or burn odors
• Commonly replaces a failed or intermittently tripping thermal safety switch
• Works as part of the appliance's temperature-safety system, not a primary temperature control

• Disconnect power to the appliance before attempting replacement
• Observe proper wiring orientation and secure terminal connections
• Replace only with the exact part specified for your appliance

This oven temperature sensor detects internal oven temperature so the control can regulate heating for even cooking and accurate bake cycles. Replaces a failed or intermittent sensor to restore proper temperature control. What it does

• Senses oven cavity temperature and sends readings to the control board
• Can cause oven to run too hot, too cool, or display temperature-related errors when failing
• Often used when bake/broil cycles are inconsistent or the oven won't reach set temperatures
• Works as the temperature feedback component for electronic oven controls

• Disconnect power to the appliance before testing or replacing the sensor
• Handle the sensor probe and wiring gently; avoid pulling on wires or kinking the lead
• Verify replacement by visually inspecting connections and testing continuity with a multimeter

This thermostat is the temperature control switch that regulates cooling cycles to help keep your refrigerator at the right temperature. Replaces a worn or faulty control to restore consistent cooling performance. What it does:

• Senses cabinet temperature and opens/closes the cooling circuit to maintain set temperature.
• Starts and stops the compressor and/or evaporator fan based on temperature demand.
• Commonly used when the fridge runs constantly, doesn't cool enough, or cycles on and off too frequently.
• Works with mechanical temperature control systems.

• Disconnect power before diagnosis and replacement to avoid electric shock.
• Mount in the original location and route capillary/tubing per original routing; avoid kinks.
• Test operation after installation by allowing the unit to run through a full cycle.

This rinse aid sensor detects the presence/level of rinse aid and signals the dishwasher control so the dispenser and cycle logic respond correctly. Replaces a failed sensor to restore proper rinse-aid detection. What it does

• Acts as a reed-style sensor that notifies the control when rinse aid is present
• Helps the dispenser and control board make rinse-aid–related decisions
• Commonly replaced when rinse-aid indicators fail or rinse-aid detection errors occur
• Small, low-voltage sensing device used in the dishwasher dispenser area

• One rinse aid sensor (reed switch)

• Disconnect power to the appliance before starting any service
• Access may require removing the door inner panel or dispenser assembly; follow the service manual
• Handle gently and avoid bending the sensor leads; ensure secure electrical connections