Whirlpool Hinge Parts

The Door Bushing is an OEM part for Whirlpool refrigerators. This part allows the smooth opening and closing of the refrigerator door by providing a smooth surface for the door hinge to pivot on. It helps ensure the door operates quietly and maintains proper alignment.

Causes of a bad door bushing can include regular wear and tear, exposure to weight stress from the door, or accidental damage.

Symptoms of a bad door bushing include:

• Door not opening or closing smoothly
• Squeaking or grinding noises when moving the door
• Door misalignment
• Increased difficulty in opening or closing the door

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Left hand hinge. For right hinge use WP8066056

This door closing cam thimble fits the refrigerator door hinge assembly. It creates the smooth ramp/detent action that helps the door self-close and seal properly, restoring consistent door movement when the original cam surfaces are worn.

• Provides the hinge cam action that pulls the door closed during the last inches of travel
• Helps keep the door aligned and reduces wobble at the hinge
• Typical symptoms of wear: door won't stay closed or bounces open, popping/clicking sounds, rough or uneven door swing, visible flat spots on cam surfaces
• Helps maintain a reliable gasket seal by guiding the door to its closed position

• Disconnect power before servicing; clear and support the door to prevent drops
• Remove hinge cover and fasteners; lift the door off the hinge as needed for access
• Replace the cam thimble on the hinge/door bracket; reassemble and tighten hardware
• Verify door alignment and full gasket contact after reinstallation

The Hinge Pin is an OEM part for Whirlpool refrigerators. This part allows the door to open and close smoothly, providing a durable pivot point for the door's movement.

Over time, hinge pins can wear down or become damaged due to the constant stress of door movement, improper alignment, or accidental force applied to the door. A compromised hinge pin can lead to issues such as difficulty in opening or closing the door, a door that hangs unevenly or doesn't seal properly, and increased wear on other door components.

Symptoms of a bad Hinge Pin include:

• Squeaking or resistance when opening or closing the door
• The door not closing fully or sealing properly
• Visible wear or damage to the pin
• The refrigerator or freezer door hanging unevenly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This oven door hinge will work for either the left or right side of an oven door. The hinges on the door are responsible for ensuring that the door can open and close properly. If one or both of the hinges are not working correctly, the door may become difficult to open and close or may not stay on the oven. If this happens, the hinges should be replaced before using the oven.Made of durable metal, the oven door hinges should last a long time. However, they can become damaged and may need to be replaced. If there is too much pressure placed on the door or hinges, it could cause them to break. Owners may want to replace both of the hinges at the same time. Be sure that the oven is off and cooled before replacing this part.The oven door hinges are for use with certain ovens from KitchenAid, Whirlpool, Inglis, and Kenmore. The hinges are genuine OEM replacement parts sourced from the manufacturer. Each hinge is sold individually. Owners that need to replace both hinges should buy two.

Color: Grey

This door stop limits the door's travel to its intended range, helping prevent overextension that can stress hinges or damage adjacent cabinetry. Replacing a worn or broken stop restores smooth, controlled door operation.

• Limits door opening/closing travel to protect hinges and alignment
• Helps maintain proper seal and fit by preventing overextension
• Replaces cracked, worn, or missing stop that allows excess movement
• Typical symptoms include door opening too far, a hard "clunk" at full travel, or visible damage to the stop

• Disconnect power; also shut off the water supply
• Support the door while servicing the hinge/stop to avoid strain
• Note the original orientation and transfer/secure fasteners firmly
• Open/close the door slowly to ensure smooth movement and proper stop action

The Closing Cam is an OEM part for Whirlpool refrigerators. The closing cam works with the door hinge and latch mechanism to make sure the refrigerator door closes securely.  

Causes of a bad closing cam can be normal wear and tear over time, excessive strain placed on the hinge areas, or damage from accidental impacts.

Symptoms of a bad closing cam include:

• Doors that do not fully close or latch properly
• Difficulty closing or opening the doors
• Increased energy costs from poor insulation
• Fruits and vegetables spoiling more quickly

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Door hinge, right hand. For left hand hinge order WP3387559

This oven door hinge is a replacement for many models of ovens. Oven doors will have two hinges. If there is a problem with one or both of the hinges, it means that the door will not open and close properly. It might not stay closed, or it could be difficult to open. This would make it impossible to use the oven, and the hinge should be replaced as soon as possible.An oven door hinge could become damaged for a host of reasons. When the door is open, too much pressure could be placed on the hinge, which could cause it to break. It could become corroded over time, or the spring might wear down. When there are issues, the owner will want to replace the hinge to ensure the door stays closed. Owners should always make sure the oven is off and not powered before beginning work.The oven door hinge will work with certain models of ovens from Whirlpool, Maytag, Amana, Jenn-Air, Norge, Crosley, and Magic Chef. This is a genuine OEM replacement part, and it is sold individually. If both of the hinges need to be replaced, the owner will need to buy two.

This hinge is for painted door only. For stainless steel door use WP8272822.

This cam-door is the small pivoting cam that helps a washer/dryer or laundry door latch and swing smoothly. Replacing a worn or broken cam restores proper door movement and helps the door close and seal reliably. What it does:

• Acts as the pivot/latch cam that guides the appliance door during opening and closing.
• Helps the door engage the latch and maintain correct alignment.
• Commonly used to stop a door from hanging, binding, or failing to stay closed.
• Can reduce door noise or catching caused by a damaged cam.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Support the door or cabinet panel during removal to prevent dropping or damage.
• Remove the door or access panel and replace the cam using basic hand tools; keep track of fasteners.
• After reassembly, check door operation and latch engagement before returning the appliance to service.

This lower door hinge supports the refrigerator door at the bottom pivot so it opens smoothly and stays properly aligned. Replacing a worn hinge can restore reliable door closure and help maintain an effective gasket seal.

• Provides the bottom pivot point and supports the door's weight
• Helps keep the door aligned for proper gasket contact
• Allows smooth opening and closing without binding
• Common symptoms of a failing hinge: door sagging, rubbing/scraping, squeaking, or not closing fully

• Disconnect power and, if applicable, shut off the water supply; remove items from the door.
• Support the door, remove the top hinge hardware, and lift the door off the bottom hinge.
• Remove the old bottom hinge from the cabinet/frame and install the new hinge in the same orientation, reusing original screws/shims.
• Reinstall the door and top hinge, then check alignment and gasket seal before restoring power.

The Dryer Door Hinge Assembly is an OEM part for Whirlpool electric and gas dryers. As a critical component, this assembly supports the dryer door and allows for smooth opening and closing. 

Causes of failure include frequent use, which causes hinge components like bushings and bearings to wear out more quickly over time. Housing cracks or mechanical loosening from repeated operation are other issues.

Symptoms of a faulty door hinge assembly include: 

• Door that won't stay closed securely or slams shut on its own   
• Difficulty smoothly opening and closing the door
• Excessive gaps around the edges that allow lint to escape

This genuine Whirlpool replacement fits Maytag, Amana, Jenn-Air, Magic Chef, and select Kenmore dryers.

The Oven Door Hinge is an OEM part for Whirlpool ovens. This hinge is essential for the proper operation of the oven door, ensuring it opens and closes smoothly and stays securely in place when shut. This hinge measures 14-1/2" in height. 

Common causes include repeated use, which can lead to wear and tear, accidental damage, or exposure to high temperatures over time. 

Symptoms of a bad oven door hinge include:

• The oven door not closing properly
• A loose or sagging oven door
• Difficulty in opening or closing the oven door
• The door not staying in the desired position

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This hinge restores smooth, stable movement of your appliance door so it opens and closes correctly, helping the door stay aligned with the frame for a proper seal and dependable everyday use. What it does:

• Provides the pivot point for the door to open and close
• Maintains door alignment to help ensure proper closing
• Replaces a bent, loose, or worn hinge that causes binding or rubbing
• Can help address issues like a door that sags, won't stay aligned, or is hard to close

• One hinge

• Disconnect power before servicing; allow hot surfaces to cool
• Support the door during removal/installation to prevent damage or injury
• Reuse existing mounting hardware unless new fasteners are supplied
• After installation, check alignment and operation before fully tightening fasteners