Whirlpool Latch, Catch, Lock Parts

The Whirlpool Dryer Door Catch is an OEM part for Whirlpool dryers. It secures the dryer door closed during operation, ensuring the safety and proper functioning of the appliance. This component engages with the door latch to hold the door shut, allowing the dryer to operate without interruption.

Causes of a bad dryer door catch can include normal wear and tear from frequent use, accidental damage, or deformation of the catch or latch that prevents proper engagement. Over time, the door catch can become loose or break, necessitating replacement to maintain the dryer's performance and safety.

Symptoms of a bad dryer door catch include:

• The dryer door not staying closed during cycles
• Difficulty closing the door securely
• The dryer stopping mid-cycle due to the door opening

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This Door Catch Bezel, in white, is an OEM part for Whirlpool dryers. It secures the dryer door, making sure it remains closed during operation. Crafted precisely to fit compatible dryer models, this bezel guarantees a secure and snug fit.

What causes a bad part:
The Door Catch Bezel might deteriorate due to frequent use, exposure to heat, or physical strain during the opening and closing of the dryer door. Additionally, prolonged exposure to cleaning agents or moisture can contribute to its degradation.

Symptoms for a bad part:

• Difficulty in securely closing the dryer door
• Loose or shaky door closure
• Visible damage or cracks on the bezel

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This bezel is a trim piece that finishes and protects the opening around a control or feature on the appliance's panel. Replacing a cracked or missing bezel restores a clean look and helps the mating control sit securely and operate properly.

• Frames the control or opening and covers raw edges for a finished appearance
• Helps keep the associated knob/button or trim aligned and seated
• Shields internal components from dust, splashes, and minor impacts
• Replace if cracked, warped, loose, or missing; symptoms can include a wobbly control, visible gaps, or cosmetic damage

• Disconnect power at the breaker before servicing; allow any hot surfaces to cool
• If applicable, pull off the knob or remove adjacent trim to access the bezel
• Release locking tabs or remove mounting screws carefully to avoid scratching the panel
• Align the new bezel with tabs/orientation marks and snap or fasten into place; reinstall parts and test

This door latch keeps the door securely closed and engages the door switch/interlock so the appliance operates as designed. Replacing a worn or broken latch helps resolve door-related errors and restores reliable, safe operation.

• Secures the door against the strike for proper closure and alignment
• Actuates the door switch/interlock so controls recognize a closed door
• Helps prevent operation when the door is open or not fully latched
• Common symptoms: door won't latch or stay closed; unit won't start or shows a "door/open-close" message; broken or loose latch hook

• Disconnect power before servicing; use proper PPE and beware of sharp edges
• Access the latch through the door panel/trim as applicable; use non-marring tools to avoid damage
• Transfer any reusable clips/springs from the old latch to the new part
• After installation, verify smooth door closure and that the control detects the door as closed

This lock cam is a small actuator that drives the appliance's door-lock mechanism. It translates the lock actuator's movement into a positive latch, helping the door lock securely when required and release correctly so cycles start and finish properly.

• Interfaces with the lock actuator and latch to engage and release the lock
• Wear, cracking, or rounding can cause the lock not to engage or to stick
• Common symptoms include a door/lid that won't lock or unlock, loose lock lever, clicking without latching, or door/lock-related error messages
• Restores proper linkage travel and switch actuation when the original cam is worn or damaged

• Disconnect power to the appliance before servicing
• Access the lock mechanism per your model; note the cam's orientation and any springs/linkages
• Install the new cam fully seated and ensure it engages the actuator and latch smoothly
• Reassemble, restore power, and test lock operation

This in the male piece on the front panel. For the female piece on the door order WPW10111905.

The Door Strike is an OEM replacement part for Whirlpool dryers. This component ensures the dryer door securely latches, enabling the appliance to operate and preventing it from running with the door ajar. It works in conjunction with the door catch to maintain a proper seal during drying cycles.

Symptoms of a bad Door Strike include:

• The dryer door not latching or staying closed
• The dryer not starting due to the door remaining open
• The door popping open during operation
• Visible wear, bending, or damage to the strike

Causes of a failing Door Strike can include regular wear and tear, misalignment from improper use, or damage from slamming the door. Replacing a faulty strike ensures the dryer operates safely and efficiently.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: metallic. Measures about 1 inch high by 2 inches deep.

This door lever actuates the latch/switch when the door closes. If it's worn or broken, the appliance may not sense a closed door and won't start. Replacing it restores proper door engagement and safe, reliable operation. What it does:

• Engages the door latch/switch mechanism so the control knows the door is closed
• Helps ensure the unit only runs with the door fully shut
• Replaces cracked, bent, or missing levers that prevent proper door sensing
• Common symptoms: won't start, must hold/push door to run, "door open" indicator stays on

• 1 door lever

• Disconnect power before servicing
• Access the latch/switch area; note the original lever's orientation and any spring
• Transfer and reuse existing hardware if needed; install the new lever in the same position
• Close the door and test for proper start/stop operation

This genuine replacement part is a door lock motor switch assembly for ovens. The door lock motor switch assembly is the part that locks the oven door. The reason it would need to be replaced is if the motor or switch has failed and is no longer able to keep the oven door locked and secured when closed. This can happen due to excessive wear and tear over time. To replace this part, start by unplugging the oven. After that, pull the oven away from the wall and proceed to remove the upper back access panel of the range. Once removed, lift the panel off and locate the lock motor and switch assembly. Disconnect the wires from the motor and switch. Once removed, unthread the two mounting screws that hold the assembly in place. Remove the connection rod. Proceed to install the new switch and motor assembly by reattaching the connection rod and refastening the mounting screws. Reattach the wires to the motor and switch and proceed to reinstall the back panel of the oven. This genuine OEM part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand ovens.

This is the keyed lock insert for select appliance doors. It lets you lock or unlock the door to secure contents and prevent unintended opening.

• Engages the door's lock mechanism to secure or release the door
• Helpful when the door won't lock/unlock or the original key is lost
• Restores proper locking function without replacing the whole lock assembly

• Unplug the appliance before service
• Verify the key profile matches your existing lock before use
• Insert fully and turn gently; do not force if resistance is felt
• Keep a spare key in a safe location away from the appliance

Replacement lid strike assembly that secures the washer lid so the machine can operate reliably. Restores proper lid engagement to help prevent the washer from stopping mid-cycle or the lid from coming unsecured during use. What it does:

• Engages with the lid latch to hold the lid closed during wash and spin cycles
• Restores proper lid alignment and secure closure when the original strike is worn, broken, or missing
• Common repair for symptoms like the lid not staying latched, the washer refusing to start, or a rattling/slipping lid

• Disconnect power before servicing the washer
• Typically installs at the lid/hinge area; may require removing the top panel or console for access
• Use basic hand tools and take care around springs and hinges to avoid injury

This strike is the catch point the latch grabs to keep the appliance door securely closed during operation. Replacing a worn or broken strike restores reliable latching so cycles can start and run properly. What it does:

• Engages with the door latch to hold the door closed during use
• Helps ensure the control senses the door is closed
• Maintains proper alignment for smooth, consistent latching
• Typical symptoms: door won't latch or stay closed, "door open" message, cycle won't start, intermittent operation when the door is moved

• 1 door strike

• Disconnect power to the appliance before servicing
• Remove the existing strike and retain mounting hardware if reusable
• Position and secure the new strike; adjust so the latch engages without forcing
• Close and test the door for smooth engagement before running a cycle

This door latch secures the appliance door and signals the control that it's safely closed. Replacing a worn or broken latch restores reliable door closure and proper cycle operation. What it does:

• Holds the door closed and aligned during use
• Engages the door strike to complete the door/lock switch circuit
• Resolve issues such as: door won't latch or pops open; cycles won't start; intermittent "door open" messages; needing to press/hold the door to run

• One door latch

• Disconnect power before servicing
• Access is typically from the door/front panel; note screw locations and latch orientation
• Transfer any mounting hardware from the original latch if needed
• After installation, verify smooth latch engagement with the strike and run a test cycle

Lid strike assembly that provides a secure catch for the washer lid so the lid latch/switch can engage, restoring proper lid closure and allowing the washer to start and complete cycles reliably. What it does:

• Serves as the catch point the lid latch engages to keep the lid closed during operation
• Enables the lid switch/lock to detect a closed lid so the machine can start and run
• Common replacement when the lid won't stay closed, the washer won't start, or lid engagement is intermittent
• Matches original mounting points for direct replacement and consistent operation

• Disconnect power to the appliance before attempting any service
• Access the strike by opening or removing the top/control panels as required for your model
• Align the strike with the lid latch, secure with the original fasteners, and ensure smooth engagement
• Reconnect power and run a short cycle to ensure proper lid detection and operation

The Washer Door Latch is an OEM part for Whirlpool washing machines. This latch is responsible for securely holding the washer door closed during operation. It plays a role in making sure there are no leaks that could damage clothing or disrupt the washing cycle.

Causes of a bad door latch can include wear and tear over time, accidental damage, or failure of the latching mechanism. 

Symptoms of a bad door latch include:

• The washer door not closing or locking fully
• Loose door that rattles or vibrates excessively
• Water leaks around the opening when the machine is running

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.