Whirlpool Spring Parts

This tension spring restores proper movement and tension for the appliance component it secures, helping the part operate smoothly and reliably. It's a simple replacement that fixes common issues caused by worn or broken springs. What it does:

• Provides tension to hold or return a moving component to its correct position
• Helps stop sagging, slipping, or loose operation of doors, latches, or levers
• Can reduce rattling or unusual noises caused by a failed spring
• Restores normal mechanical action when the original spring is stretched or broken

• Disconnect power to the appliance before starting any repair
• Springs can be under tension—use appropriate tools and wear eye/hand protection
• Compare the new spring to the old one for length, coil size, and end fittings before installation

For Whirlpool made dishwashers. Assembly includes one spring, one retainer and one protective tip. Replace both springs at the same time to prevent uneven load.

Replacement interlock spring that provides tension for the appliance door latch so the door closes and the interlock switch can engage for normal operation. Restores reliable door engagement and latch return in compatible Whirlpool appliances. What it does:

• Provides tension to the door latch/interlock assembly so the door stays securely closed during use.
• Ensures the latch returns to the closed position and allows the interlock switch to complete the appliance's safety circuit.
• Helps resolve symptoms such as a loose or non-returning latch, door that won't stay closed, or cycles that stop because the door won't engage.
• Works as a direct replacement for the listed interlock spring in compatible Whirlpool assemblies.

• Disconnect power to the appliance before servicing to avoid electric shock or injury.
• Basic hand tools are typically required; panels or the door may need partial disassembly—refer to the model's service guide.
• Inspect the latch, striker, and interlock switch for wear or damage and replace if needed; improper installation can prevent correct engagement.

A replacement solenoid spring that restores proper plunger return and tension for compatible Whirlpool solenoid assemblies. Replaces worn or broken springs to help ensure reliable actuator movement and consistent operation. What it does

• Provides return tension for the solenoid plunger so the actuator snaps back after activation
• Helps restore normal solenoid movement when a worn spring causes sticking or weak response
• Commonly used when the appliance fails to engage, release, or cycle components driven by a solenoid
• Works as a direct-fit spring for the matching solenoid assembly when part is specified

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Remove access panels and the solenoid assembly to access the spring.
• Handle small parts carefully; note placement and orientation of the spring for correct reassembly.
• If other solenoid or actuator components are damaged or corroded, replace the entire assembly for reliable operation.

This tension spring provides the restoring force needed for smooth operation of the appliance mechanism. It replaces a worn or broken spring to restore proper movement and reduce rattling or sagging parts. What it does

• Supplies tension to return or hold moving components in place.
• Helps stabilize doors, levers, or internal linkages so they operate smoothly.
• Restores correct alignment and reliable motion when installed correctly.

• One tension spring (single piece as shown)

• Disconnect power and, if applicable, gas supply before beginning any repair.
• Use appropriate hand tools and wear eye protection; springs can release suddenly.
• Verify correct orientation and attachment points against the appliance service manual or parts diagram.

This spring provides tension for the door hinge, helping the door open and close smoothly and stay properly balanced. Replacing a weakened or broken spring restores correct door movement and prevents slamming or drooping.

• Maintains tension on the door hinge mechanism
• Helps the door stay level and close securely
• Can reduce issues like a sagging, loose, or slamming door
• Restores smooth, controlled door operation

• Disconnect power and shut off gas or water (as applicable) before service
• Support the door to relieve hinge tension prior to removal
• Note spring orientation/routing before replacing
• Wear cut-resistant gloves; hinge areas can be sharp and under tension

Replacement tension spring for Whirlpool appliances that restores proper tension and smooth movement to moving parts. Use this spring to address issues caused by a weak or broken spring so components operate more reliably. What it does

• Provides tension for moving components to maintain alignment and proper operation
• Helps restore secure closure and prevents sagging or slipping of doors, panels or linkages
• Reduces binding, dragging or uneven motion in hinges and pivot points
• Replaces worn or broken spring to return the mechanism to factory movement

• Disconnect power and shut off fuel before servicing the appliance
• Springs can be under tension — wear eye and hand protection and use the correct tools
• Follow the OEM service manual or parts diagram for correct routing and attachment