Whirlpool Valve

If your dishwasher shuts off mid-cycle or leaks water, a warped or stuck overfill float may be the cause. This 5-minute fix restores proper fill control.

This smart electronic valve regulates on/off flow inside the appliance under command of the control system, helping the unit fill, dispense, or operate as designed. A precise, electronically driven valve is critical for consistent performance.

• Opens and closes when energized to start or stop flow to the connected system
• Coordinates with the control board for timed, accurate operation
• Helps prevent overfill or underfill conditions
• Common symptoms of a failing valve: no fill/flow, slow or intermittent flow, continuous flow when off, leaks from the valve body, or related fill/flow error codes

• Disconnect power and shut off the appliance's supply line upstream before servicing
• Keep towels or a container handy to catch residual fluid when lines are disconnected
• Transfer connectors and any reusable brackets from the old valve to the new one, matching orientation
• After installation, restore supply and power, then check all connections for leaks and proper operation

Converting your portable dishwasher to built-in? This conversion kit includes all mounting hardware and adapters needed for permanent installation.

Ice maker not filling or overflowing? Water inlet valve controls flow to your ice maker. Stops slow fills, excess water, and seepage. DIY repair.

Replacement water inlet valve that controls water flow into the refrigerator's dispenser and ice maker, restoring proper filling and preventing overflows. Direct-fit design replaces the original valve on compatible Whirlpool refrigerators. What it does:

• Regulates water flow from the household supply to the refrigerator dispenser and ice maker.
• Opens when the dispenser or ice maker calls for water and closes to stop flow and prevent overfilling.
• Common symptoms: no water from the dispenser, slow/weak fill, ice maker not filling, or water leaking at the valve.
• Designed to match the original valve's function and plumbing connections for straightforward replacement.

• Disconnect power to the appliance and shut off the water supply before starting any work.
• Use basic hand tools to remove and reinstall mounting screws and water line fittings; support lines to avoid stress on fittings.
• Inspect and replace any damaged O-rings or supply tubing; tighten fittings securely but avoid overtightening.
• After installation, turn water on slowly, check all connections for leaks, then restore power and verify dispenser/ice maker operation.

Fix a dishwasher that won't fill or leaks water with a new inlet valve. Common repair for filling issues and water seepage. DIY-friendly replacement part.

Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.

No water from door dispenser or ice maker? A faulty water inlet valve stops water flow. This valve restores fill cycles. Most DIYers complete in 30 minutes.

Fix a burner that won't light or ignite, won't adjust flame, or has a frozen stem. This gas burner valve controls flow for proper ignition and heat.

This gas valve controls the flow of natural gas or propane to the oven/range burner, restoring reliable ignition and steady heat for baking and broiling. Direct replacement for failed or leaking valve assemblies. What it does:

• Regulates gas flow to the oven/range burner so the burner lights and maintains temperature.
• Stops gas flow when the safety system detects a fault, preventing unsafe conditions.
• Commonly replaces valves that leak, fail to open, or prevent the oven from heating.
• Helps resolve symptoms like no bake/broil heat, intermittent ignition, or continuous clicking/try-to-light cycles.

• One gas valve assembly.

• Turn off gas supply and electrical power before attempting service; follow local codes.
• Tighten gas fittings to manufacturer torque specs and perform a leak test after installation.
• Some installations may require removing the range/oven front or burner components for access.

Fix a burner that won't light or has an uneven flame with this gas cooktop valve. Controls gas flow to a single burner for reliable ignition and heat.

Burner won't light or flame is uneven? This top burner valve controls gas flow to restore reliable ignition and consistent flame on your gas range.

Fix burners that won't light, won't adjust, or have uneven flames with this gas cooktop burner valve. Controls gas flow to individual burners.

A replacement gas valve that controls gas flow to the oven or range burner, restoring safe ignition and flame regulation so the appliance heats reliably. Designed to match OEM fit and restore proper gas delivery. What it does:

• Opens and closes to regulate gas flow to the burner or oven for ignition and sustained flame
• Helps resolve symptoms like no ignition, intermittent flame, or burners that won't stay lit when valve failure is confirmed
• Works with the appliance's safety and control systems to enable normal heating cycles
• Replaces a failed or leaking valve when diagnostics show the valve is the faulty component

• One gas valve

• Installation requires shutting off the gas supply and disconnecting power first; follow all local codes
• Tighten gas line connections to the manufacturer's torque specs and check for leaks with a soap solution or gas leak detector
• Verify valve part number and appliance compatibility before installation

Fix dishwasher overflows or won't fill issues. This water level float detects proper fill levels. Replaces broken or stuck floats causing drainage problems.