Whirlpool Valve

Replaced water inlet valve Read more

I ordered from this company expecting the parts to be later than they said and the parts showed up in 2 days like they said. Just before the Easter holiday even. Amazingly fast. Very satisfied!!! Washer is up and running again. Great job on getting me my parts! Thank you! Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water

Ordered this part and just changed it out. Not hard once I figured out how to get in to it. Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

• Not dispensing water

Replaced water valve to fix water not going to door, easy enough to do. Replaced icemaker which was corroded inside the cube-forming trays causing black flakes to come off stuck to the ice cubes, and was also leaking causing the water to drip into the ice bucket making one giant ice cube. Ten-minute job, which took an hour and a half. this is a 25-year-old unit and I only had access to the plug on the back of the icemaker, the other end was behind the rear wall. The wire was simply not long... Read more

I called AppliancePartsPros to find a replacement water inlet valve. They talked me through finding the clothes washer model number. Once the model number was located, the AppliancePartsPros person on the phone found the correct replacement valve. I received the valve 3-5 days after ordering. I downloaded the clothes washer repair manual and watched some YouTube videos regarding valve replacement. I followed the steps in the repair manual being careful to mark anything I had removed during... Read more

New valve. Read more

The problem wasn't a blocked screen. I took apart my washer. Very easy on the Kenmore 600 series. Before I did this, I watched a YouTube video and it was a piece of cake. The whole job took me 35 minutes. Read more

I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately. Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it... Read more

Watched a couple of videos that closely matched my project. Warranty company couldn't find a service tech in my area so they had to refund my stove purchase. Part cost under $50. Refund: $950!! Read more

Removed front kick plate, found overflow valve assembly leaking . When parts arrived removed and replaced overflow valve. Took about 10 minutes Read more

• Will not fill with water

After researching on line I was able to narrow down the problem to either the cold water of hot water fill valve. These valves are electronically controlled and can go bad thus causing the washing machine to not fill properly. Nf stands for "no fill". I replaced the cold water valve first which was held by two screws and a couple of wires. It literally took me 5 minutes to replace the part. As soon as I started the wash cycle I could tell I had fixed the problem because the humming noise that... Read more

After researching on line I was able to narrow down the problem to either the cold water of hot water fill valve. These valves are electronically controlled and can go bad thus causing the washing machine to not fill properly. Nf stands for "no fill". I replaced the cold water valve first which was held by two screws and a couple of wires. It literally took me 5 minutes to replace the part. As soon as I started the wash cycle I could tell I had fixed the problem because the humming noise that... Read more

REPLACED ENTIRE WATER CONTROL SYSTEM. Being quite anal about my planning projects, I played a Youtube video about this job. I screen captured the important steps, printed them out and taped above the washer. It was a good approach because it gave me a valid reference of the wiring harness reinstallation. Overall, the project was easier than I thought. Great results. Momma is pleased and is no longer complaining that we have to buy a new $1,000 washer ! Read more

Removed cover from icemaker, unplugged refrigerator and tested with meter. Coil of water inlet valve tested open. Ordered part and replaced. Works like a charm. Read more

Bought a new water valve assembly Read more