Whirlpool Washer Parts

I used youtube to look for diagnostic and then took my washer apart all of a sudden the front loader was no longer fun, I cleaned out the trap that was full checked all other lines and put back together. After putting back together the door would not lock because one of the connectors was loose. I say this to remind you to check all the connectors. Jumping forward take apart put back together. Tested failed would not drain still. Looked for pump everywhere and found you guys. I was buying... Read more

• Will not fill with water
• Leaking

SCREWED IT ONTO FAUCET Read more

• Won't start

I was searching the web for solutions and came across two folks who had similar trouble code. One fixed his by removing the pump strainer from the pump to find coins blocking water flow, thus the analog water pressure sensor provided a failure response. My issue was solved by following the other hints I got. I ordered a new sensor (switch). It was expensive for what it is, but the washer will not run correctly without it! The part arrived in a very timely manner, and it was the right part.... Read more

• No heat or not enough heat

I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more

I ordered the male and female door latching parts. Read more

After much reading on line regarding my problem. I decided to do any test that I could to try to diagnose and fix this myself if I could. This took a lot of time and patience to get the answers on how to go about this from "experts" as some of the info was contradictory. I was almost about to give up and buy a new washer with less electronic parts and buttons as advised by an honest appliance technician . I tried one more thing first which was to disconnect the lead wires connected to the MCU .... Read more

Once you tilt the washer and prop it against something it's a pretty straight forward and easy fix. If you watch the instructional "How-to" video beforehand, the repair should take between 30 to 60 minutes. It all depends on your skill level and if everything goes smoothly. Make sure you have all the proper tools, grease and blue thread lock at the ready to help you move this repair along faster. This repair was in conjunction with replacing the motor position sensor. I didn't know I needed a... Read more

We started getting the F06 code when on the normal cycle it was time to Rinse/Spin, pointing to a speed/tachometer issue on the motor. After several attempts of unplugging from power and restarting the cycle it would eventually start working for the rest of the laundry session. The Whirlpool technician after a brief look on the underside determined it was the motor and had to be replaced, even tough all troubleshooting tests on the motor were ok. I insisted that the probability was much higher... Read more

Tested capacitor Read more

Googled it. Saw the YouTube video on replacing the User Interface module. Decided to try to fix this myself. Looked simple enough. Ordered the UI module. Saw the video on the replacement again. Read more

I called parts pro and they had my part and sent it right to me I am soooooooo happy with this company they are amazing. I only ordered 1 baffle and now I'm calling them to order the other 2 baffles. Thank you so much for your help and service. Read more

Put in new lid lock. This is my second one in 1 year. Whirlpool suggested I leave it loose so that if somebody did try and force it open, it wouldn't break it. This lid lock has 4 wires and cannot be bypassed. Read more

The parts I purchased from Appliance Parts Pro fit perfectly and were reasonably priced. I received them the next day, which made the Wife (and me) very happy. Although Appliance Parts Pro did not have a repair video for this, I was able to find one online and the machine is washing like new again. The website is well laid out and easy to find what your looking for. Between the available parts and the videos they provide, anyone who is reasonably handy should be able to repair their machine as... Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Replace the Mainboard control and push the start button. Read more

The drying agent lid was broken for a couple years now and our dishes would never dry completely. We finally decided to google for Kenmore parts and this website came up. Couldn't believe how easy it was. All we had to do was find the brand and model number and all the parts showed up on Appliancepartspros.com website. We scanned thru the list found the lid and ordered. It arrived within 2 days. Viola!! Now we wish we had done this much earlier. Thank you for such a smooth experience. Read more