Amana Dryer Parts

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

I replaced the part i ordered and it worked great! Read more

The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow. Some professionals say that if one of these sensors fail, both... Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

I watched the video at your website. I unplugged the electric first. When I opened up the machine up, It was loaded with lint.I found the source was a hole in the vent tube outside the machine. I fixed that first . The lint had been sucked back into the machine. The first half hour was spent vacuuming out all the lint and then I could proceeded with the motor change. I followed the video exactly. I removed the screws at the two front corners, after lifting the top and controls and tying it... Read more

• Will not tumble

Replaced the tension pulley assembly, drum rollers, drum roller axles, belt, and drum glides while I had the dryer disassembled. It turned out that the cause of the squeak was the tension pulley assembly, however it was easy and economical enough to replace anything that could have been the cause of the squeaking while I had the dryer apart. The parts were ordered on Thursday afternoon and delivered on Friday. I had the dryer repaired and running like new in no time. For about $100, it was... Read more

Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping! Read more

I ordered the male and female door latching parts. Read more

Ordered the freezer door switch and the light. Replaced the freezer door switch and the light and everything is back to normal. Replaced both in less than 15 min with no problems. Read more

I followed the video on the parts page and had the part replaced in no time. My dryer door was slightly different than the example, but the concept was the same. My part arrived the next day and the repair took less than a half-hour. Extremely satisfied with this site Read more

Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping! Read more

Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more

My husband took the old timer out and replace it with the new. Now it worked fine. Being we order the other parts we decided to replace them. Read more

I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more

• Too hot
• tripping breaker

I found the assembly with heater element, thermostat, and the thermal fuse already assembled (cheaper than finding what part was bad and ordering that one part). unplugged dryer, pulled it out and removed the dryer exhaust tube, the top and front. The harness was a little short so I wasnt able to pull the whole heater assembly out before disconnecting. BEFORE disconnecting I took a picture so that if my brain forgot what wires went were!!!! put the dryer back together and put a load that just... Read more

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more