Amana Parts

Replaced both hot and cold water inlet valves. Works like a charm, issue resolved. Read more

It took less then 15 min. Read more

• No heat or not enough heat
• Takes too long to dry

Since finding out pulley on motor is factory installed, I had to order a new motor with new pulley on it. I could not remove old blower wheel from old motor, no matter how hard I tried so I had to purchase new blower wheel and new blower housing. I am super happy finding Appliancepartspros.com the prices, and my experience was great! I basically removed everything step by step, and then replaced with the new parts step by step. I had help by watching videos that were provided online before and... Read more

• Little to no heat when broiling
• Little to no heat when baking
• Gas igniter glows, but will not light
• Won't start

Replaced the igniter, Simple but there are several points to remember. TURN THE POWER OFF 1) remove the oven door or you will have a hard time reaching the back of the oven. Mine just lifted off. 2) The igniter tip is fragile put a drop cloth over the oven floor in case you drop it even after it is in its holder. 3) The drop cloth will catch screws too if you drop them so they won't fall into the oven. 4) The cable from the oven is very short even after pulling it out from the hole at the back.... Read more

I referenced the repair video. Very straightforward and easy. Only need 3 tools: 1/4 and 5/16 nut drivers and Philips head screwdriver. About 15 minute job. Surprising how much lint and dust build up inside the chassis, was able to clean that out too. Read more

• Ice maker dispenses too little ice
• Ice maker won't dispense ice

Plastic drum was broken and wasn't pushing the ice through the crusher teeth. Received my part pronto and made the repair. Was an easy fix, took about 15 min from start to finish. Everything working very good now. ( : Thanks for getting the parts to me so fast. I will definitely remember Appliance Pro if I need parts in the future. Read more

Replaced the front burner switch with this switch. Works good as new now. Read more

Touch up paint Read more

• Will not agitate
• Spins slowly
• Burning smell
• Pumps but will not spin

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

Bought this door gasket and watched the video, very easy if you just take your time and start in one corner and go to the opposite corner. this way it stretches the seal completely into each corner. do as the video says and it will go great. Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

I watched the videos for both jobs, which were excellent and "spot on" for the repair jobs.It didn't take me an hour to replace both lines. Keep up the good work on helping us repair and save money doing our own work. Ken Read more

It was a learning experience. First I turned off the power! I removed the lower kick plate, disconnected the drain hose and electrical connectors. Then removed the discharge pump and heat sensor then loosened the 4 hold down arms/clamps. Then I opened the door and pulled the base up from the inside. Now to remove and replace the Pump Motor. Then reverse the process. If I were to do again, I'd pull the dishwasher out and lay it on its back. Read more

• Will not drain
• Burning smell
• Noisy

18 year old Maytag Atlantis top load washer had a load knocking and rattle sound with excessive vibration when the tub was spinning, but not when it was agitating. They was no water leaking. I took the front panel off and carefully listened while I ran a cycle and the loud sound sounded like it was coming from the drain pump. So I took off the drive belt and noticed that it was glazed and that there was belt material on the drain pump and tub transmission pulleys. I removed the drain pump and... Read more

• Door won't close

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

Replaced the entire mechanism with a new one. Read more