Amana Parts

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

• Marks left on clothes

After replacing thermal fuse once and having it fail a second time, I had to dig a little deeper to uncover the problem. I checked for blockage in the vent but everything was clear. I did, however, find that the drum had some up and down play in it. After closer inspection, I could see that the front drum seal was actually worn to the point that I could see a gap between the seal and the drum. I figured that the gap in the seal was letting air in and not letting sufficient air flow through the... Read more

Viewed YouTube video of AppliancePartsPros.com replacing the agitator to see if I could do it myself. I ordered part from Sears but they never delivered. Cancelled order with Sears, ordered from APP and was sent part within 24hrs by fedex for less than Sears charged. Will only go APP and would recommend APP to everyone. Using the video I easily replaced the part and our washer is back in business! Thank you APP!!!!! Read more

Called in. Talk to a sale rep. Told them the model number, told me that this part would work. Shipped it to me. Snapped it in about 30 seconds. Part was perfect. Read more

Used screwdriver to push in plastic tabs holding old unit to the top of the refrigerator box Read more

Although I only needed to replace the drawer support (end cap) on the right side the kit comes with replacements for both sides. I was surprised to see that the air flow adjustment mechanism that is located on the right side end cap was not included. I should mention that I did not disassemble the drawer mechanisms before ordering the end cap(s). The kit contained only the two molded end caps - no fasteners, mechanisms, or anything else. It turns out that this was all perfectly fine. The... Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Replaced it with a new seal Read more

Put in new LED lighrt module you sent me Read more

Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more

• Not dispensing water
• Leaking

Being an ex maintainence. person, I went down and turned off the water supply. Then I started to try to find the leak by removing the rear covers for the compressor and valves. Once removing a couple of covers where the dual valve was, I spotted where the water was coming from.I then pulled the electrical plug from the wall. Between the solenoid and valve. I removed the screws that held the valve in place. Then disconnected the three hoses going into valve and removed the two electrical... Read more

With your helpful video we replaced the water filter housing. That repair fixed problem. Read more

I watched the videos for both jobs, which were excellent and "spot on" for the repair jobs.It didn't take me an hour to replace both lines. Keep up the good work on helping us repair and save money doing our own work. Ken Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Touch up paint Read more

• Ice maker dispenses too little ice
• Ice maker won't dispense ice

Plastic drum was broken and wasn't pushing the ice through the crusher teeth. Received my part pronto and made the repair. Was an easy fix, took about 15 min from start to finish. Everything working very good now. ( : Thanks for getting the parts to me so fast. I will definitely remember Appliance Pro if I need parts in the future. Read more