Amana Parts

• Too hot
• Takes too long to dry
• Doesn't shut off

Did google search and found youtube diagnostic and repair video. Blower wheel was warped and rubbing on the cover. We ordered a new blower wheel and followed youtube instructions to install new blower wheel. Read more

I had previously replaced the transmission in my two year old Whirlpool Cabrio washing machine. Overall it was in good shape but gets heavy use. That repair was approximately $200 and worked for several months. Recently it began leaking. At first I thought it was the tub-to-shaft seal. I replaced this part but it was still leaking. It turns out it was the simplest of things... The drain hose was not connected very well! I replaced the drain hose ($11 part) and while I was at it I... Read more

Took the whole dryer apart to access the wheels (4) of them, belt and fan wheel, also had to clean all the lint out that somehow builds up inside the dryer. Plus cleaned out dryer duct vent, added to the time involved. If you are planning on fixing the dryer because of a noise which was in my case, I highly recommend buy all the parts for complete maintenance mentioned above. What helped save me time? I watch a dryer fan wheel replacement training video first, highly recommend this!... Read more

I ordered the hinge on the weekend and it came on Tuesday in the late Morning. I loved how quick it arrived. The swap out of the part took 10 minutes using a batter powered driver, a #2 Phillips tip and a T-25 tip. If you use hand tools, it will take a few minutes longer. If I would have realized how easy it was, I would have replaced it when it started sagging instead of waiting for it to break. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Replaced water inlet unit. Read more

Ordered and paid for two day shipping and received on time. Read more

• Not dispensing water
• Ice maker not making ice
• Leaking

A piece of cake. Video was spot on. Finish less than 45 min. Read more

Replaced It With New One Read more

Heating element nut had cracked causing a leak. Rather than run right out and buy a new one, I found the cracked nut and replaced it for about 11.00. Thank you Appliance pros. Quick shipping. Read more

I look on the internet i came a cross appliance parts pros i didnt no what i was looking for so i call the phone number talk to someone gave him the info he ask for they has what i was looking for in stock the guy was very nice he say i will get the part in two days and i got it in two days if i need a part for anything else i will ckeck out appliance parts pros when the door gasket came my grandson put it on in a flash Read more

I took the new seal out of it's packaging and used a blowdryer on low heat to soften up the seal so that the crease from shipping (it was folded to ship) disappeared. Next I took the refrigerator door off, removed the old seal, & cleaned the area where the new seal would be applied. Following the video on the Appliance Pro Parts website, I re-installed the new seal and put the door back on. Last step was to snap on the new hinge cap I ordered. The video online was easy to follow and this... Read more

For about the last month or so the clothes (especially sheets) would just roll into a ball (like a big sausage) the wouldn't dry. Kept readjusting the clothes. I went on the internet to see what the issue could be and found lots of advise about shaking out the sheet and clothes first, using tennis balls, and using fuller or smaller loads. None of that worked. But I finally figured out that the reason they roll into a ball is because the belt around the drum is slipping or stretched. This... Read more

I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more

Replaced agitator and washplate bolt and washer. Normally this would have been a 5 min job, however the bolt wouldn't come loose. The teeth on the agitator were worn down and the shaft the bolt screws into would turn with the bolt when trying to loosen it. I had to cut out the agitator using a dremel and hold the shaft in place with a vise grip in order to unscrew the bolt. Once the bolt was out I used WD-40 to help get the agitator off the gears. Job took much longer than normal, but I... Read more

I'm not an appliance mechanic and have never worked on a dryer before, but I have worked as an instrument technician and lightly dabbled in HVAC repairs. We moved from natural gas to a new home with propane, so purchased this kit to make the conversion. In my mind I thought it would be fairly quick and easy, change a few fittings, etc, but realized upon reading the instructions that I needed to disassemble most of the dryer. The work was straightforward but since this was my first time... Read more