Cooktop Hinge Parts

For Stainless Models.

This hinge kit restores smooth, secure door movement so your appliance opens and closes correctly. Replacing worn hinge components helps eliminate sagging and misalignment that can keep the door from sealing and operating as designed. What it does:

• Supports and pivots the door for controlled opening and closing
• Maintains door alignment to help ensure proper latch/seal engagement
• Helps address symptoms like door sagging, binding, squeaking, or not closing flush
• Reduces stress on mounting points to extend component life

• One hinge kit

• Disconnect power before servicing; also shut off water supply
• Support the door while removing hinge fasteners to prevent damage or injury
• Transfer any spacers/shims from the old hinge and tighten fasteners securely
• Adjust as needed per your model's service instructions

This hinge kit restores a refrigerator door's secure attachment so the door opens, closes and seals properly. Install to correct sagging, misalignment or noisy pivot points and help maintain consistent cabinet closure. What it does:

• Secures the appliance door to the cabinet and provides the pivot point for smooth movement
• Restores proper door alignment to help improve sealing and reduce air gaps
• Replaces worn or bent hinge hardware that can cause door sagging or rubbing
• Reduces creaks, binding or uneven door movement when operating the door

• Disconnect power to the appliance and remove food from the door before starting
• Support the door during removal and installation to prevent drops or damage
• Tighten hardware securely but avoid over-torquing; verify door alignment and seal after installation
• Follow OEM instructions for your model before ordering

This door hinge provides the pivot point that lets the appliance door open smoothly and close flush. Replacing a worn or bent hinge restores proper alignment and sealing for safe, reliable door operation.

• Provides the pivot point that guides door opening and closing
• Helps keep the door square to the cabinet for a consistent seal
• Wear or damage can cause sagging, binding, gaps, or a door that won't close flush
• Restores smooth movement and proper door alignment

• Disconnect power before servicing; also shut off gas or water
• Support the door during removal to prevent damage or injury
• Transfer any mounting screws/brackets from the old hinge to the new one
• After installation, verify door alignment and gasket contact; adjust as needed

The Oven Door Hinge is an OEM part for Bosch ranges and ovens. It securely holds the oven door in proper alignment while enabling smooth opening and closing.

Causes of a bad oven door hinge include wear and stress from years of use. Repeated opening and closing of a heavy oven door subjects the hinge to constant pressure that can lead to degradation or failure over time.

Symptoms of a bad oven door hinge include:

• A door that sags or won't stay properly aligned when closed
• Difficulty fully opening or closing the oven door
• Noise or looseness felt at the hinge when operating the door

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Hinge-Door is an OEM component specifically designed for Whirlpool gas ranges. It is the stainless steel door hinge assembly that allows smooth, controlled movement of the oven door. The hinges support the weight of the door and maintain proper alignment between the door and oven cavity.

Symptoms of bad door hinges include:

• Loose, wobbly, or sagging door that does not stay firmly in place
• Difficulty in fully opening or closing the door 
• Excessive noise or vibration from the hinges
• Pinholes, cracks, or other damage to the hinge surface

Causes of failure are typically wear over the heavy usage life of a range. Hinges may also become misaligned or damaged by accidental impact.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely. Replacing a worn hinge restores proper alignment and sealing to help the door latch correctly and operate as designed.

• Provides the pivot point and maintains door alignment
• Helps ensure smooth opening/closing and proper latching
• Supports a tight seal to prevent gaps, rattles, or temperature/moisture loss
• Typical failure signs: door sags, binds, squeaks, or won't stay closed/aligned

• Disconnect power before service; wear gloves to protect from sharp edges
• Support the door and control any spring tension; remove mounting hardware and the old hinge
• Install the new hinge in the same orientation; transfer any reusable hardware
• Adjust as needed

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal